BGP
BGP stands for Border Gateway Protocol. The latest BGP version is 4. BGP-4 is one of the Exterior Gateway Protocols and the de facto standard interdomain routing protocol. BGP-4 is described in RFC 1771 and updated by RFC 4271. RFC 2858 adds multiprotocol support to BGP-4.
Basic Concepts
Autonomous Systems
From RFC 1930:
An AS is a connected group of one or more IP prefixes run by one or more network operators which has a SINGLE and CLEARLY DEFINED routing policy.
Each AS has an identifying number associated with it called an ASN. This is a two octet value ranging in value from 1 to 65535. The AS numbers 64512 through 65535 are defined as private AS numbers. Private AS numbers must not be advertised on the global Internet.
The ASN is one of the essential elements of BGP. BGP is a distance vector routing protocol, and the AS-Path framework provides distance vector metric and loop detection to BGP.
See also
Address Families
Multiprotocol extensions enable BGP to carry routing information for multiple network layer protocols. BGP supports an Address Family Identifier (AFI) for IPv4 and IPv6. Support is also provided for multiple sets of per-AFI information via the BGP Subsequent Address Family Identifier (SAFI). FRR supports SAFIs for unicast information, labeled information (RFC 3107 and RFC 8277), and Layer 3 VPN information (RFC 4364 and RFC 4659).
Route Selection
The route selection process used by FRR’s BGP implementation uses the following decision criterion, starting at the top of the list and going towards the bottom until one of the factors can be used.
Weight check
Prefer higher local weight routes to lower routes.
Local preference check
Prefer higher local preference routes to lower.
If
bgp bestpath aigp
is enabled, and both paths that are compared have AIGP attribute, BGP uses AIGP tie-breaking unless both of the paths have the AIGP metric attribute. This means that the AIGP attribute is not evaluated during the best path selection process between two paths when one path does not have the AIGP attribute.Local route check
Prefer local routes (statics, aggregates, redistributed) to received routes.
AS path length check
Prefer shortest hop-count AS_PATHs.
Origin check
Prefer the lowest origin type route. That is, prefer IGP origin routes to EGP, to Incomplete routes.
MED check
Where routes with a MED were received from the same AS, prefer the route with the lowest MED. Multi-Exit Discriminator.
External check
Prefer the route received from an external, eBGP peer over routes received from other types of peers.
IGP cost check
Prefer the route with the lower IGP cost.
Multi-path check
If multi-pathing is enabled, then check whether the routes not yet distinguished in preference may be considered equal. If
bgp bestpath as-path multipath-relax
is set, all such routes are considered equal, otherwise routes received via iBGP with identical AS_PATHs or routes received from eBGP neighbours in the same AS are considered equal.Already-selected external check
Where both routes were received from eBGP peers, then prefer the route which is already selected. Note that this check is not applied if
bgp bestpath compare-routerid
is configured. This check can prevent some cases of oscillation.Router-ID check
Prefer the route with the lowest router-ID. If the route has an ORIGINATOR_ID attribute, through iBGP reflection, then that router ID is used, otherwise the router-ID of the peer the route was received from is used.
Cluster-List length check
The route with the shortest cluster-list length is used. The cluster-list reflects the iBGP reflection path the route has taken.
Peer address
Prefer the route received from the peer with the higher transport layer address, as a last-resort tie-breaker.
Capability Negotiation
When adding IPv6 routing information exchange feature to BGP. There were some proposals. IETF IDR adopted a proposal called Multiprotocol Extension for BGP. The specification is described in RFC 2283. The protocol does not define new protocols. It defines new attributes to existing BGP. When it is used exchanging IPv6 routing information it is called BGP-4+. When it is used for exchanging multicast routing information it is called MBGP.
bgpd supports Multiprotocol Extension for BGP. So if a remote peer supports the protocol, bgpd can exchange IPv6 and/or multicast routing information.
Traditional BGP did not have the feature to detect a remote peer’s capabilities, e.g. whether it can handle prefix types other than IPv4 unicast routes. This was a big problem using Multiprotocol Extension for BGP in an operational network. RFC 2842 adopted a feature called Capability Negotiation. bgpd use this Capability Negotiation to detect the remote peer’s capabilities. If a peer is only configured as an IPv4 unicast neighbor, bgpd does not send these Capability Negotiation packets (at least not unless other optional BGP features require capability negotiation).
By default, FRR will bring up peering with minimal common capability for the both sides. For example, if the local router has unicast and multicast capabilities and the remote router only has unicast capability the local router will establish the connection with unicast only capability. When there are no common capabilities, FRR sends Unsupported Capability error and then resets the connection.
BGP Router Configuration
ASN and Router ID
First of all you must configure BGP router with the router bgp ASN
command. The AS number is an identifier for the autonomous system. The AS
identifier can either be a number or two numbers separated by a period. The
BGP protocol uses the AS identifier for detecting whether the BGP connection is
internal or external.
- router bgp ASN
Enable a BGP protocol process with the specified ASN. After this statement you can input any BGP Commands.
- bgp router-id A.B.C.D
This command specifies the router-ID. If bgpd connects to zebra it gets interface and address information. In that case default router ID value is selected as the largest IP Address of the interfaces. When router zebra is not enabled bgpd can’t get interface information so router-id is set to 0.0.0.0. So please set router-id by hand.
Multiple Autonomous Systems
FRR’s BGP implementation is capable of running multiple autonomous systems at once. Each configured AS corresponds to a VRF. In the past, to get the same functionality the network administrator had to run a new bgpd process; using VRFs allows multiple autonomous systems to be handled in a single process.
When using multiple autonomous systems, all router config blocks after the first one must specify a VRF to be the target of BGP’s route selection. This VRF must be unique within respect to all other VRFs being used for the same purpose, i.e. two different autonomous systems cannot use the same VRF. However, the same AS can be used with different VRFs.
Note
The separated nature of VRFs makes it possible to peer a single bgpd process to itself, on one machine. Note that this can be done fully within BGP without a corresponding VRF in the kernel or Zebra, which enables some practical use cases such as route reflectors and route servers.
Configuration of additional autonomous systems, or of a router that targets a specific VRF, is accomplished with the following command:
- router bgp ASN vrf VRFNAME
VRFNAME
is matched against VRFs configured in the kernel. Whenvrf VRFNAME
is not specified, the BGP protocol process belongs to the default VRF.
An example configuration with multiple autonomous systems might look like this:
router bgp 1
neighbor 10.0.0.1 remote-as 20
neighbor 10.0.0.2 remote-as 30
!
router bgp 2 vrf blue
neighbor 10.0.0.3 remote-as 40
neighbor 10.0.0.4 remote-as 50
!
router bgp 3 vrf red
neighbor 10.0.0.5 remote-as 60
neighbor 10.0.0.6 remote-as 70
...
See also
See also
Views
In addition to supporting multiple autonomous systems, FRR’s BGP implementation also supports views.
BGP views are almost the same as normal BGP processes, except that routes selected by BGP are not installed into the kernel routing table. Each BGP view provides an independent set of routing information which is only distributed via BGP. Multiple views can be supported, and BGP view information is always independent from other routing protocols and Zebra/kernel routes. BGP views use the core instance (i.e., default VRF) for communication with peers.
- router bgp AS-NUMBER view NAME
Make a new BGP view. You can use an arbitrary word for the
NAME
. Routes selected by the view are not installed into the kernel routing table.With this command, you can setup Route Server like below.
! router bgp 1 view 1 neighbor 10.0.0.1 remote-as 2 neighbor 10.0.0.2 remote-as 3 ! router bgp 2 view 2 neighbor 10.0.0.3 remote-as 4 neighbor 10.0.0.4 remote-as 5
- show [ip] bgp view NAME
Display the routing table of BGP view
NAME
.
Route Selection
- bgp bestpath as-path confed
This command specifies that the length of confederation path sets and sequences should should be taken into account during the BGP best path decision process.
- bgp bestpath as-path multipath-relax
This command specifies that BGP decision process should consider paths of equal AS_PATH length candidates for multipath computation. Without the knob, the entire AS_PATH must match for multipath computation.
- bgp bestpath compare-routerid
Ensure that when comparing routes where both are equal on most metrics, including local-pref, AS_PATH length, IGP cost, MED, that the tie is broken based on router-ID.
If this option is enabled, then the already-selected check, where already selected eBGP routes are preferred, is skipped.
If a route has an ORIGINATOR_ID attribute because it has been reflected, that ORIGINATOR_ID will be used. Otherwise, the router-ID of the peer the route was received from will be used.
The advantage of this is that the route-selection (at this point) will be more deterministic. The disadvantage is that a few or even one lowest-ID router may attract all traffic to otherwise-equal paths because of this check. It may increase the possibility of MED or IGP oscillation, unless other measures were taken to avoid these. The exact behaviour will be sensitive to the iBGP and reflection topology.
- bgp bestpath peer-type multipath-relax
This command specifies that BGP decision process should consider paths from all peers for multipath computation. If this option is enabled, paths learned from any of eBGP, iBGP, or confederation neighbors will be multipath if they are otherwise considered equal cost.
- bgp bestpath aigp
Use the bgp bestpath aigp command to evaluate the AIGP attribute during the best path selection process between two paths that have the AIGP attribute.
When bgp bestpath aigp is disabled, BGP does not use AIGP tie-breaking rules unless paths have the AIGP attribute.
Disabled by default.
- maximum-paths (1-128)
Sets the maximum-paths value used for ecmp calculations for this bgp instance in EBGP. The maximum value listed, 128, can be limited by the ecmp cli for bgp or if the daemon was compiled with a lower ecmp value. This value can also be set in ipv4/ipv6 unicast/labeled unicast to only affect those particular afi/safi’s.
- maximum-paths ibgp (1-128) [equal-cluster-length]
Sets the maximum-paths value used for ecmp calculations for this bgp instance in IBGP. The maximum value listed, 128, can be limited by the ecmp cli for bgp or if the daemon was compiled with a lower ecmp value. This value can also be set in ipv4/ipv6 unicast/labeled unicast to only affect those particular afi/safi’s.
Administrative Distance Metrics
- distance bgp (1-255) (1-255) (1-255)
This command changes distance value of BGP. The arguments are the distance values for external routes, internal routes and local routes respectively.
- distance (1-255) A.B.C.D/M
- distance (1-255) A.B.C.D/M WORD
Sets the administrative distance for a particular route.
Require policy on EBGP
- bgp ebgp-requires-policy
This command requires incoming and outgoing filters to be applied for eBGP sessions as part of RFC-8212 compliance. Without the incoming filter, no routes will be accepted. Without the outgoing filter, no routes will be announced.
This is enabled by default.
When you enable/disable this option you MUST clear the session.
When the incoming or outgoing filter is missing you will see “(Policy)” sign under
show bgp summary
:exit1# show bgp summary IPv4 Unicast Summary (VRF default): BGP router identifier 10.10.10.1, local AS number 65001 vrf-id 0 BGP table version 4 RIB entries 7, using 1344 bytes of memory Peers 2, using 43 KiB of memory Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc 192.168.0.2 4 65002 8 10 0 0 0 00:03:09 5 (Policy) N/A fe80:1::2222 4 65002 9 11 0 0 0 00:03:09 (Policy) (Policy) N/A
Additionally a show bgp neighbor command would indicate in the For address family: block that:
exit1# show bgp neighbor ... For address family: IPv4 Unicast Update group 1, subgroup 1 Packet Queue length 0 Inbound soft reconfiguration allowed Community attribute sent to this neighbor(all) Inbound updates discarded due to missing policy Outbound updates discarded due to missing policy 0 accepted prefixes
Reject routes with AS_SET or AS_CONFED_SET types
- bgp reject-as-sets
This command enables rejection of incoming and outgoing routes having AS_SET or AS_CONFED_SET type.
Suppress duplicate updates
- bgp suppress-duplicates
For example, BGP routers can generate multiple identical announcements with empty community attributes if stripped at egress. This is an undesired behavior. Suppress duplicate updates if the route actually not changed. Default: enabled.
Send Hard Reset CEASE Notification for Administrative Reset
- bgp hard-administrative-reset
Send Hard Reset CEASE Notification for ‘Administrative Reset’ events.
When disabled, and Graceful Restart Notification capability is exchanged between the peers, Graceful Restart procedures apply, and routes will be retained.
Enabled by default.
Disable checking if nexthop is connected on EBGP sessions
- bgp disable-ebgp-connected-route-check
This command is used to disable the connection verification process for EBGP peering sessions that are reachable by a single hop but are configured on a loopback interface or otherwise configured with a non-directly connected IP address.
Route Flap Dampening
- bgp dampening (1-45) (1-20000) (1-50000) (1-255)
This command enables BGP route-flap dampening and specifies dampening parameters.
- half-life
Half-life time for the penalty
- reuse-threshold
Value to start reusing a route
- suppress-threshold
Value to start suppressing a route
- max-suppress
Maximum duration to suppress a stable route
The route-flap damping algorithm is compatible with RFC 2439. The use of this command is not recommended nowadays.
At the moment, route-flap dampening is not working per VRF and is working only for IPv4 unicast and multicast.
Multi-Exit Discriminator
The BGP MED attribute has properties which can cause subtle convergence problems in BGP. These properties and problems have proven to be hard to understand, at least historically, and may still not be widely understood. The following attempts to collect together and present what is known about MED, to help operators and FRR users in designing and configuring their networks.
The BGP MED attribute is intended to allow one AS to indicate its preferences for its ingress points to another AS. The MED attribute will not be propagated on to another AS by the receiving AS - it is ‘non-transitive’ in the BGP sense.
E.g., if AS X and AS Y have 2 different BGP peering points, then AS X might set a MED of 100 on routes advertised at one and a MED of 200 at the other. When AS Y selects between otherwise equal routes to or via AS X, AS Y should prefer to take the path via the lower MED peering of 100 with AS X. Setting the MED allows an AS to influence the routing taken to it within another, neighbouring AS.
In this use of MED it is not really meaningful to compare the MED value on routes where the next AS on the paths differs. E.g., if AS Y also had a route for some destination via AS Z in addition to the routes from AS X, and AS Z had also set a MED, it wouldn’t make sense for AS Y to compare AS Z’s MED values to those of AS X. The MED values have been set by different administrators, with different frames of reference.
The default behaviour of BGP therefore is to not compare MED values across routes received from different neighbouring ASes. In FRR this is done by comparing the neighbouring, left-most AS in the received AS_PATHs of the routes and only comparing MED if those are the same.
Unfortunately, this behaviour of MED, of sometimes being compared across routes and sometimes not, depending on the properties of those other routes, means MED can cause the order of preference over all the routes to be undefined. That is, given routes A, B, and C, if A is preferred to B, and B is preferred to C, then a well-defined order should mean the preference is transitive (in the sense of orders [1]) and that A would be preferred to C.
However, when MED is involved this need not be the case. With MED it is possible that C is actually preferred over A. So A is preferred to B, B is preferred to C, but C is preferred to A. This can be true even where BGP defines a deterministic ‘most preferred’ route out of the full set of A,B,C. With MED, for any given set of routes there may be a deterministically preferred route, but there need not be any way to arrange them into any order of preference. With unmodified MED, the order of preference of routes literally becomes undefined.
That MED can induce non-transitive preferences over routes can cause issues. Firstly, it may be perceived to cause routing table churn locally at speakers; secondly, and more seriously, it may cause routing instability in iBGP topologies, where sets of speakers continually oscillate between different paths.
The first issue arises from how speakers often implement routing decisions. Though BGP defines a selection process that will deterministically select the same route as best at any given speaker, even with MED, that process requires evaluating all routes together. For performance and ease of implementation reasons, many implementations evaluate route preferences in a pair-wise fashion instead. Given there is no well-defined order when MED is involved, the best route that will be chosen becomes subject to implementation details, such as the order the routes are stored in. That may be (locally) non-deterministic, e.g.: it may be the order the routes were received in.
This indeterminism may be considered undesirable, though it need not cause problems. It may mean additional routing churn is perceived, as sometimes more updates may be produced than at other times in reaction to some event .
This first issue can be fixed with a more deterministic route selection that
ensures routes are ordered by the neighbouring AS during selection.
bgp deterministic-med
. This may reduce the number of updates as routes
are received, and may in some cases reduce routing churn. Though, it could
equally deterministically produce the largest possible set of updates in
response to the most common sequence of received updates.
A deterministic order of evaluation tends to imply an additional overhead of sorting over any set of n routes to a destination. The implementation of deterministic MED in FRR scales significantly worse than most sorting algorithms at present, with the number of paths to a given destination. That number is often low enough to not cause any issues, but where there are many paths, the deterministic comparison may quickly become increasingly expensive in terms of CPU.
Deterministic local evaluation can not fix the second, more major, issue of MED however. Which is that the non-transitive preference of routes MED can cause may lead to routing instability or oscillation across multiple speakers in iBGP topologies. This can occur with full-mesh iBGP, but is particularly problematic in non-full-mesh iBGP topologies that further reduce the routing information known to each speaker. This has primarily been documented with iBGP route-reflection topologies. However, any route-hiding technologies potentially could also exacerbate oscillation with MED.
This second issue occurs where speakers each have only a subset of routes, and there are cycles in the preferences between different combinations of routes - as the undefined order of preference of MED allows - and the routes are distributed in a way that causes the BGP speakers to ‘chase’ those cycles. This can occur even if all speakers use a deterministic order of evaluation in route selection.
E.g., speaker 4 in AS A might receive a route from speaker 2 in AS X, and from speaker 3 in AS Y; while speaker 5 in AS A might receive that route from speaker 1 in AS Y. AS Y might set a MED of 200 at speaker 1, and 100 at speaker 3. I.e, using ASN:ID:MED to label the speakers:
.
/---------------\\
X:2------|--A:4-------A:5--|-Y:1:200
Y:3:100--|-/ |
\\---------------/
Assuming all other metrics are equal (AS_PATH, ORIGIN, 0 IGP costs), then based on the RFC4271 decision process speaker 4 will choose X:2 over Y:3:100, based on the lower ID of 2. Speaker 4 advertises X:2 to speaker 5. Speaker 5 will continue to prefer Y:1:200 based on the ID, and advertise this to speaker 4. Speaker 4 will now have the full set of routes, and the Y:1:200 it receives from 5 will beat X:2, but when speaker 4 compares Y:1:200 to Y:3:100 the MED check now becomes active as the ASes match, and now Y:3:100 is preferred. Speaker 4 therefore now advertises Y:3:100 to 5, which will also agrees that Y:3:100 is preferred to Y:1:200, and so withdraws the latter route from 4. Speaker 4 now has only X:2 and Y:3:100, and X:2 beats Y:3:100, and so speaker 4 implicitly updates its route to speaker 5 to X:2. Speaker 5 sees that Y:1:200 beats X:2 based on the ID, and advertises Y:1:200 to speaker 4, and the cycle continues.
The root cause is the lack of a clear order of preference caused by how MED sometimes is and sometimes is not compared, leading to this cycle in the preferences between the routes:
.
/---> X:2 ---beats---> Y:3:100 --\\
| |
| |
\\---beats--- Y:1:200 <---beats---/
This particular type of oscillation in full-mesh iBGP topologies can be
avoided by speakers preferring already selected, external routes rather than
choosing to update to new a route based on a post-MED metric (e.g. router-ID),
at the cost of a non-deterministic selection process. FRR implements this, as
do many other implementations, so long as it is not overridden by setting
bgp bestpath compare-routerid
, and see also
Route Selection.
However, more complex and insidious cycles of oscillation are possible with iBGP route-reflection, which are not so easily avoided. These have been documented in various places. See, e.g.:
for concrete examples and further references.
There is as of this writing no known way to use MED for its original purpose; and reduce routing information in iBGP topologies; and be sure to avoid the instability problems of MED due the non-transitive routing preferences it can induce; in general on arbitrary networks.
There may be iBGP topology specific ways to reduce the instability risks, even while using MED, e.g.: by constraining the reflection topology and by tuning IGP costs between route-reflector clusters, see RFC 3345 for details. In the near future, the Add-Path extension to BGP may also solve MED oscillation while still allowing MED to be used as intended, by distributing “best-paths per neighbour AS”. This would be at the cost of distributing at least as many routes to all speakers as a full-mesh iBGP would, if not more, while also imposing similar CPU overheads as the “Deterministic MED” feature at each Add-Path reflector.
More generally, the instability problems that MED can introduce on more complex, non-full-mesh, iBGP topologies may be avoided either by:
Setting
bgp always-compare-med
, however this allows MED to be compared across values set by different neighbour ASes, which may not produce coherent desirable results, of itself.Effectively ignoring MED by setting MED to the same value (e.g.: 0) using
set metric METRIC
on all received routes, in combination with settingbgp always-compare-med
on all speakers. This is the simplest and most performant way to avoid MED oscillation issues, where an AS is happy not to allow neighbours to inject this problematic metric.
As MED is evaluated after the AS_PATH length check, another possible use for MED is for intra-AS steering of routes with equal AS_PATH length, as an extension of the last case above. As MED is evaluated before IGP metric, this can allow cold-potato routing to be implemented to send traffic to preferred hand-offs with neighbours, rather than the closest hand-off according to the IGP metric.
Note that even if action is taken to address the MED non-transitivity issues, other oscillations may still be possible. E.g., on IGP cost if iBGP and IGP topologies are at cross-purposes with each other - see the Flavel and Roughan paper above for an example. Hence the guideline that the iBGP topology should follow the IGP topology.
- bgp deterministic-med
Carry out route-selection in way that produces deterministic answers locally, even in the face of MED and the lack of a well-defined order of preference it can induce on routes. Without this option the preferred route with MED may be determined largely by the order that routes were received in.
Setting this option will have a performance cost that may be noticeable when there are many routes for each destination. Currently in FRR it is implemented in a way that scales poorly as the number of routes per destination increases.
The default is that this option is not set.
Note that there are other sources of indeterminism in the route selection process, specifically, the preference for older and already selected routes from eBGP peers, Route Selection.
- bgp always-compare-med
Always compare the MED on routes, even when they were received from different neighbouring ASes. Setting this option makes the order of preference of routes more defined, and should eliminate MED induced oscillations.
If using this option, it may also be desirable to use
set metric METRIC
to set MED to 0 on routes received from external neighbours.This option can be used, together with
set metric METRIC
to use MED as an intra-AS metric to steer equal-length AS_PATH routes to, e.g., desired exit points.
Graceful Restart
BGP graceful restart functionality as defined in RFC-4724 defines the mechanisms that allows BGP speaker to continue to forward data packets along known routes while the routing protocol information is being restored.
Usually, when BGP on a router restarts, all the BGP peers detect that the session went down and then came up. This “down/up” transition results in a “routing flap” and causes BGP route re-computation, generation of BGP routing updates, and unnecessary churn to the forwarding tables.
The following functionality is provided by graceful restart:
The feature allows the restarting router to indicate to the helping peer the routes it can preserve in its forwarding plane during control plane restart by sending graceful restart capability in the OPEN message sent during session establishment.
The feature allows helping router to advertise to all other peers the routes received from the restarting router which are preserved in the forwarding plane of the restarting router during control plane restart.
(R1)-----------------------------------------------------------------(R2)
1. BGP Graceful Restart Capability exchanged between R1 & R2.
<--------------------------------------------------------------------->
2. Kill BGP Process at R1.
---------------------------------------------------------------------->
3. R2 Detects the above BGP Restart & verifies BGP Restarting
Capability of R1.
4. Start BGP Process at R1.
5. Re-establish the BGP session between R1 & R2.
<--------------------------------------------------------------------->
6. R2 Send initial route updates, followed by End-Of-Rib.
<----------------------------------------------------------------------
7. R1 was waiting for End-Of-Rib from R2 & which has been received
now.
8. R1 now runs BGP Best-Path algorithm. Send Initial BGP Update,
followed by End-Of Rib
<--------------------------------------------------------------------->
BGP-GR Preserve-Forwarding State
BGP OPEN message carrying optional capabilities for Graceful Restart has 8 bit “Flags for Address Family” for given AFI and SAFI. This field contains bit flags relating to routes that were advertised with the given AFI and SAFI.
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|F| Reserved |
+-+-+-+-+-+-+-+-+
The most significant bit is defined as the Forwarding State (F) bit, which can be used to indicate whether the forwarding state for routes that were advertised with the given AFI and SAFI has indeed been preserved during the previous BGP restart. When set (value 1), the bit indicates that the forwarding state has been preserved. The remaining bits are reserved and MUST be set to zero by the sender and ignored by the receiver.
- bgp graceful-restart preserve-fw-state
FRR gives us the option to enable/disable the “F” flag using this specific vty command. However, it doesn’t have the option to enable/disable this flag only for specific AFI/SAFI i.e. when this command is used, it applied to all the supported AFI/SAFI combinations for this peer.
End-of-RIB (EOR) message
An UPDATE message with no reachable Network Layer Reachability Information (NLRI) and empty withdrawn NLRI is specified as the End-of-RIB marker that can be used by a BGP speaker to indicate to its peer the completion of the initial routing update after the session is established.
For the IPv4 unicast address family, the End-of-RIB marker is an UPDATE message with the minimum length. For any other address family, it is an UPDATE message that contains only the MP_UNREACH_NLRI attribute with no withdrawn routes for that <AFI, SAFI>.
Although the End-of-RIB marker is specified for the purpose of BGP graceful restart, it is noted that the generation of such a marker upon completion of the initial update would be useful for routing convergence in general, and thus the practice is recommended.
Route Selection Deferral Timer
Specifies the time the restarting router defers the route selection process after restart.
Restarting Router : The usage of route election deferral timer is specified in https://tools.ietf.org/html/rfc4724#section-4.1
Once the session between the Restarting Speaker and the Receiving Speaker is re-established, the Restarting Speaker will receive and process BGP messages from its peers.
However, it MUST defer route selection for an address family until it either.
Receives the End-of-RIB marker from all its peers (excluding the ones with the “Restart State” bit set in the received capability and excluding the ones that do not advertise the graceful restart capability).
The Selection_Deferral_Timer timeout.
- bgp graceful-restart select-defer-time (0-3600)
This is command, will set deferral time to value specified.
- bgp graceful-restart rib-stale-time (1-3600)
This is command, will set the time for which stale routes are kept in RIB.
- bgp graceful-restart restart-time (0-4095)
Set the time to wait to delete stale routes before a BGP open message is received.
Using with Long-lived Graceful Restart capability, this is recommended setting this timer to 0 and control stale routes with
bgp long-lived-graceful-restart stale-time
.Default value is 120.
- bgp graceful-restart stalepath-time (1-4095)
This is command, will set the max time (in seconds) to hold onto restarting peer’s stale paths.
It also controls Enhanced Route-Refresh timer.
If this command is configured and the router does not receive a Route-Refresh EoRR message, the router removes the stale routes from the BGP table after the timer expires. The stale path timer is started when the router receives a Route-Refresh BoRR message.
- bgp graceful-restart notification
Indicate Graceful Restart support for BGP NOTIFICATION messages.
After changing this parameter, you have to reset the peers in order to advertise N-bit in Graceful Restart capability.
Without Graceful-Restart Notification capability (N-bit not set), GR is not activated when receiving CEASE/HOLDTIME expire notifications.
When sending
CEASE/Administrative Reset
(clear bgp
), the session is closed and routes are not retained. When N-bit is set andbgp hard-administrative-reset
is turned off Graceful-Restart is activated and routes are retained.Enabled by default.
BGP Per Peer Graceful Restart
Ability to enable and disable graceful restart, helper and no GR at all mode functionality at peer level.
So bgp graceful restart can be enabled at modes global BGP level or at per peer level. There are two FSM, one for BGP GR global mode and other for peer per GR.
Default global mode is helper and default peer per mode is inherit from global. If per peer mode is configured, the GR mode of this particular peer will override the global mode.
BGP GR Global Mode Commands
- bgp graceful-restart
This command will enable BGP graceful restart functionality at the global level.
- bgp graceful-restart disable
This command will disable both the functionality graceful restart and helper mode.
BGP GR Peer Mode Commands
- neighbor A.B.C.D graceful-restart
This command will enable BGP graceful restart functionality at the peer level.
- neighbor A.B.C.D graceful-restart-helper
This command will enable BGP graceful restart helper only functionality at the peer level.
- neighbor A.B.C.D graceful-restart-disable
This command will disable the entire BGP graceful restart functionality at the peer level.
Long-lived Graceful Restart
Currently, only restarter mode is supported. This capability is advertised only if graceful restart capability is negotiated.
- bgp long-lived-graceful-restart stale-time (1-16777215)
Specifies the maximum time to wait before purging long-lived stale routes for helper routers.
Default is 0, which means the feature is off by default. Only graceful restart takes into account.
Administrative Shutdown
- bgp shutdown [message MSG...]
Administrative shutdown of all peers of a bgp instance. Drop all BGP peers, but preserve their configurations. The peers are notified in accordance with RFC 8203 by sending a
NOTIFICATION
message with error codeCease
and subcodeAdministrative Shutdown
prior to terminating connections. This global shutdown is independent of the neighbor shutdown, meaning that individually shut down peers will not be affected by lifting it.An optional shutdown message MSG can be specified.
Networks
- network A.B.C.D/M
This command adds the announcement network.
router bgp 1 address-family ipv4 unicast network 10.0.0.0/8 exit-address-family
This configuration example says that network 10.0.0.0/8 will be announced to all neighbors. Some vendors’ routers don’t advertise routes if they aren’t present in their IGP routing tables; bgpd doesn’t care about IGP routes when announcing its routes.
- bgp network import-check
This configuration modifies the behavior of the network statement. If you have this configured the underlying network must exist in the rib. If you have the [no] form configured then BGP will not check for the networks existence in the rib. default is the network must exist.
IPv6 Support
- neighbor A.B.C.D activate
This configuration modifies whether to enable an address family for a specific neighbor. By default only the IPv4 unicast address family is enabled.
router bgp 1 address-family ipv6 unicast neighbor 2001:0DB8::1 activate network 2001:0DB8:5009::/64 exit-address-family
This configuration example says that network 2001:0DB8:5009::/64 will be announced and enables the neighbor 2001:0DB8::1 to receive this announcement.
By default, only the IPv4 unicast address family is announced to all neighbors. Using the ‘no bgp default ipv4-unicast’ configuration overrides this default so that all address families need to be enabled explicitly.
router bgp 1 no bgp default ipv4-unicast neighbor 10.10.10.1 remote-as 2 neighbor 2001:0DB8::1 remote-as 3 address-family ipv4 unicast neighbor 10.10.10.1 activate network 192.168.1.0/24 exit-address-family address-family ipv6 unicast neighbor 2001:0DB8::1 activate network 2001:0DB8:5009::/64 exit-address-family
This configuration demonstrates how the ‘no bgp default ipv4-unicast’ might be used in a setup with two upstreams where each of the upstreams should only receive either IPv4 or IPv6 announcements.
Using the
bgp default ipv6-unicast
configuration, IPv6 unicast address family is enabled by default for all new neighbors.
Route Aggregation
Route Aggregation-IPv4 Address Family
- aggregate-address A.B.C.D/M
This command specifies an aggregate address.
In order to advertise an aggregated prefix, a more specific (longer) prefix MUST exist in the BGP table. For example, if you want to create an
aggregate-address 10.0.0.0/24
, you should make sure you have something like10.0.0.5/32
or10.0.0.0/26
, or any other smaller prefix in the BGP table. The routing information table (RIB) is not enough, you have to redistribute them into the BGP table.
- aggregate-address A.B.C.D/M route-map NAME
Apply a route-map for an aggregated prefix.
- aggregate-address A.B.C.D/M origin <egp|igp|incomplete>
Override ORIGIN for an aggregated prefix.
- aggregate-address A.B.C.D/M as-set
This command specifies an aggregate address. Resulting routes include AS set.
- aggregate-address A.B.C.D/M summary-only
This command specifies an aggregate address.
Longer prefixes advertisements of more specific routes to all neighbors are suppressed.
- aggregate-address A.B.C.D/M matching-MED-only
Configure the aggregated address to only be created when the routes MED match, otherwise no aggregated route will be created.
- aggregate-address A.B.C.D/M suppress-map NAME
Similar to summary-only, but will only suppress more specific routes that are matched by the selected route-map.
This configuration example sets up an
aggregate-address
under the ipv4 address-family.router bgp 1 address-family ipv4 unicast aggregate-address 10.0.0.0/8 aggregate-address 20.0.0.0/8 as-set aggregate-address 40.0.0.0/8 summary-only aggregate-address 50.0.0.0/8 route-map aggr-rmap exit-address-family
Route Aggregation-IPv6 Address Family
- aggregate-address X:X::X:X/M
This command specifies an aggregate address.
- aggregate-address X:X::X:X/M route-map NAME
Apply a route-map for an aggregated prefix.
- aggregate-address X:X::X:X/M origin <egp|igp|incomplete>
Override ORIGIN for an aggregated prefix.
- aggregate-address X:X::X:X/M as-set
This command specifies an aggregate address. Resulting routes include AS set.
- aggregate-address X:X::X:X/M summary-only
This command specifies an aggregate address.
Longer prefixes advertisements of more specific routes to all neighbors are suppressed
- aggregate-address X:X::X:X/M matching-MED-only
Configure the aggregated address to only be created when the routes MED match, otherwise no aggregated route will be created.
- aggregate-address X:X::X:X/M suppress-map NAME
Similar to summary-only, but will only suppress more specific routes that are matched by the selected route-map.
This configuration example sets up an
aggregate-address
under the ipv6 address-family.router bgp 1 address-family ipv6 unicast aggregate-address 10::0/64 aggregate-address 20::0/64 as-set aggregate-address 40::0/64 summary-only aggregate-address 50::0/64 route-map aggr-rmap exit-address-family
Redistribution
Redistribution configuration should be placed under the address-family
section for the specific AF to redistribute into. Protocol availability for
redistribution is determined by BGP AF; for example, you cannot redistribute
OSPFv3 into address-family ipv4 unicast
as OSPFv3 supports IPv6.
- redistribute <connected|isis|kernel|ospf|ospf6|rip|ripng|static|table> [metric (0-4294967295)] [route-map WORD]
Redistribute routes from other protocols into BGP.
- bgp update-delay MAX-DELAY ESTABLISH-WAIT
This feature is used to enable read-only mode on BGP process restart or when a BGP process is cleared using ‘clear ip bgp *’. Note that this command is configured at the global level and applies to all bgp instances/vrfs. It cannot be used at the same time as the “update-delay” command described below, which is entered in each bgp instance/vrf desired to delay update installation and advertisements. The global and per-vrf approaches to defining update-delay are mutually exclusive.
When applicable, read-only mode would begin as soon as the first peer reaches Established status and a timer for max-delay seconds is started. During this mode BGP doesn’t run any best-path or generate any updates to its peers. This mode continues until:
All the configured peers, except the shutdown peers, have sent explicit EOR (End-Of-RIB) or an implicit-EOR. The first keep-alive after BGP has reached Established is considered an implicit-EOR. If the establish-wait optional value is given, then BGP will wait for peers to reach established from the beginning of the update-delay till the establish-wait period is over, i.e. the minimum set of established peers for which EOR is expected would be peers established during the establish-wait window, not necessarily all the configured neighbors.
max-delay period is over.
On hitting any of the above two conditions, BGP resumes the decision process and generates updates to its peers.
Default max-delay is 0, i.e. the feature is off by default.
- update-delay MAX-DELAY
- update-delay MAX-DELAY ESTABLISH-WAIT
This feature is used to enable read-only mode on BGP process restart or when a BGP process is cleared using ‘clear ip bgp *’. Note that this command is configured under the specific bgp instance/vrf that the feature is enabled for. It cannot be used at the same time as the global “bgp update-delay” described above, which is entered at the global level and applies to all bgp instances. The global and per-vrf approaches to defining update-delay are mutually exclusive.
When applicable, read-only mode would begin as soon as the first peer reaches Established status and a timer for max-delay seconds is started. During this mode BGP doesn’t run any best-path or generate any updates to its peers. This mode continues until:
All the configured peers, except the shutdown peers, have sent explicit EOR (End-Of-RIB) or an implicit-EOR. The first keep-alive after BGP has reached Established is considered an implicit-EOR. If the establish-wait optional value is given, then BGP will wait for peers to reach established from the beginning of the update-delay till the establish-wait period is over, i.e. the minimum set of established peers for which EOR is expected would be peers established during the establish-wait window, not necessarily all the configured neighbors.
max-delay period is over.
On hitting any of the above two conditions, BGP resumes the decision process and generates updates to its peers.
Default max-delay is 0, i.e. the feature is off by default.
- table-map ROUTE-MAP-NAME
This feature is used to apply a route-map on route updates from BGP to Zebra. All the applicable match operations are allowed, such as match on prefix, next-hop, communities, etc. Set operations for this attach-point are limited to metric and next-hop only. Any operation of this feature does not affect BGPs internal RIB.
Supported for ipv4 and ipv6 address families. It works on multi-paths as well, however, metric setting is based on the best-path only.
Peers
Defining Peers
- neighbor PEER remote-as ASN
Creates a new neighbor whose remote-as is ASN. PEER can be an IPv4 address or an IPv6 address or an interface to use for the connection.
router bgp 1 neighbor 10.0.0.1 remote-as 2
In this case my router, in AS-1, is trying to peer with AS-2 at 10.0.0.1.
This command must be the first command used when configuring a neighbor. If the remote-as is not specified, bgpd will complain like this:
can't find neighbor 10.0.0.1
- neighbor PEER remote-as internal
Create a peer as you would when you specify an ASN, except that if the peers ASN is different than mine as specified under the
router bgp ASN
command the connection will be denied.
- neighbor PEER remote-as external
Create a peer as you would when you specify an ASN, except that if the peers ASN is the same as mine as specified under the
router bgp ASN
command the connection will be denied.
- bgp listen range <A.B.C.D/M|X:X::X:X/M> peer-group PGNAME
Accept connections from any peers in the specified prefix. Configuration from the specified peer-group is used to configure these peers.
Note
When using BGP listen ranges, if the associated peer group has TCP MD5 authentication configured, your kernel must support this on prefixes. On Linux, this support was added in kernel version 4.14. If your kernel does not support this feature you will get a warning in the log file, and the listen range will only accept connections from peers without MD5 configured.
Additionally, we have observed that when using this option at scale (several hundred peers) the kernel may hit its option memory limit. In this situation you will see error messages like:
bgpd: sockopt_tcp_signature: setsockopt(23): Cannot allocate memory
In this case you need to increase the value of the sysctl
net.core.optmem_max
to allow the kernel to allocate the necessary option
memory.
- bgp listen limit <1-65535>
Define the maximum number of peers accepted for one BGP instance. This limit is set to 100 by default. Increasing this value will really be possible if more file descriptors are available in the BGP process.
- coalesce-time (0-4294967295)
The time in milliseconds that BGP will delay before deciding what peers can be put into an update-group together in order to generate a single update for them. The default time is 1000.
Configuring Peers
- neighbor PEER shutdown [message MSG...] [rtt (1-65535) [count (1-255)]]
Shutdown the peer. We can delete the neighbor’s configuration by
no neighbor PEER remote-as ASN
but all configuration of the neighbor will be deleted. When you want to preserve the configuration, but want to drop the BGP peer, use this syntax.Optionally you can specify a shutdown message MSG.
Also, you can specify optionally
rtt
in milliseconds to automatically shutdown the peer if round-trip-time becomes higher than defined.Additional
count
parameter is the number of keepalive messages to count before shutdown the peer if round-trip-time becomes higher than defined.
- neighbor PEER disable-connected-check
Allow peerings between directly connected eBGP peers using loopback addresses.
- neighbor PEER disable-link-bw-encoding-ieee
- neighbor PEER extended-optional-parameters
Force Extended Optional Parameters Length format to be used for OPEN messages.
By default, it’s disabled. If the standard optional parameters length is higher than one-octet (255), then extended format is enabled automatically.
For testing purposes, extended format can be enabled with this command.
- neighbor PEER ebgp-multihop
Specifying
ebgp-multihop
allows sessions with eBGP neighbors to establish when they are multiple hops away. When the neighbor is not directly connected and this knob is not enabled, the session will not establish.If the peer’s IP address is not in the RIB and is reachable via the default route, then you have to enable
ip nht resolve-via-default
.
- neighbor PEER description ...
Set description of the peer.
- neighbor PEER interface IFNAME
When you connect to a BGP peer over an IPv6 link-local address, you have to specify the IFNAME of the interface used for the connection. To specify IPv4 session addresses, see the
neighbor PEER update-source
command below.
- neighbor PEER interface remote-as <internal|external|ASN>
Configure an unnumbered BGP peer.
PEER
should be an interface name. The session will be established via IPv6 link locals. Useinternal
for iBGP andexternal
for eBGP sessions, or specify an ASN if you wish.
- neighbor PEER next-hop-self [force]
This command specifies an announced route’s nexthop as being equivalent to the address of the bgp router if it is learned via eBGP. This will also bypass third-party next-hops in favor of the local bgp address. If the optional keyword
force
is specified the modification is done also for routes learned via iBGP.
- neighbor PEER attribute-unchanged [{as-path|next-hop|med}]
This command specifies attributes to be left unchanged for advertisements sent to a peer. Use this to leave the next-hop unchanged in ipv6 configurations, as the route-map directive to leave the next-hop unchanged is only available for ipv4.
- neighbor PEER update-source <IFNAME|ADDRESS>
Specify the IPv4 source address to use for the BGP session to this neighbour, may be specified as either an IPv4 address directly or as an interface name (in which case the zebra daemon MUST be running in order for bgpd to be able to retrieve interface state).
router bgp 64555 neighbor foo update-source 192.168.0.1 neighbor bar update-source loopback0
- neighbor PEER default-originate [route-map WORD]
bgpd’s default is to not announce the default route (0.0.0.0/0) even if it is in routing table. When you want to announce default routes to the peer, use this command.
If
route-map
keyword is specified, then the default route will be originated only if route-map conditions are met. For example, announce the default route only if10.10.10.10/32
route exists and set an arbitrary community for a default route.router bgp 64555 address-family ipv4 unicast neighbor 192.168.255.1 default-originate route-map default ! ip prefix-list p1 seq 5 permit 10.10.10.10/32 ! route-map default permit 10 match ip address prefix-list p1 set community 123:123 !
- neighbor PEER port PORT
- neighbor PEER password PASSWORD
Set a MD5 password to be used with the tcp socket that is being used to connect to the remote peer. Please note if you are using this command with a large number of peers on linux you should consider modifying the net.core.optmem_max sysctl to a larger value to avoid out of memory errors from the linux kernel.
- neighbor PEER send-community
- neighbor PEER weight WEIGHT
This command specifies a default weight value for the neighbor’s routes.
- neighbor PEER maximum-prefix NUMBER [force]
Sets a maximum number of prefixes we can receive from a given peer. If this number is exceeded, the BGP session will be destroyed.
In practice, it is generally preferable to use a prefix-list to limit what prefixes are received from the peer instead of using this knob. Tearing down the BGP session when a limit is exceeded is far more destructive than merely rejecting undesired prefixes. The prefix-list method is also much more granular and offers much smarter matching criterion than number of received prefixes, making it more suited to implementing policy.
If
force
is set, then ALL prefixes are counted for maximum instead of accepted only. This is useful for cases where an inbound filter is applied, but you want maximum-prefix to act on ALL (including filtered) prefixes. This option requires soft-reconfiguration inbound to be enabled for the peer.
- neighbor PEER maximum-prefix-out NUMBER
Sets a maximum number of prefixes we can send to a given peer.
Since sent prefix count is managed by update-groups, this option creates a separate update-group for outgoing updates.
- neighbor PEER local-as AS-NUMBER [no-prepend] [replace-as]
Specify an alternate AS for this BGP process when interacting with the specified peer. With no modifiers, the specified local-as is prepended to the received AS_PATH when receiving routing updates from the peer, and prepended to the outgoing AS_PATH (after the process local AS) when transmitting local routes to the peer.
If the no-prepend attribute is specified, then the supplied local-as is not prepended to the received AS_PATH.
If the replace-as attribute is specified, then only the supplied local-as is prepended to the AS_PATH when transmitting local-route updates to this peer.
Note that replace-as can only be specified if no-prepend is.
This command is only allowed for eBGP peers.
- neighbor <A.B.C.D|X:X::X:X|WORD> as-override
Override AS number of the originating router with the local AS number.
Usually this configuration is used in PEs (Provider Edge) to replace the incoming customer AS number so the connected CE (Customer Edge) can use the same AS number as the other customer sites. This allows customers of the provider network to use the same AS number across their sites.
This command is only allowed for eBGP peers.
- neighbor <A.B.C.D|X:X::X:X|WORD> allowas-in [<(1-10)|origin>]
Accept incoming routes with AS path containing AS number with the same value as the current system AS.
This is used when you want to use the same AS number in your sites, but you can’t connect them directly. This is an alternative to neighbor WORD as-override.
The parameter (1-10) configures the amount of accepted occurrences of the system AS number in AS path.
The parameter origin configures BGP to only accept routes originated with the same AS number as the system.
This command is only allowed for eBGP peers.
- neighbor <A.B.C.D|X:X::X:X|WORD> addpath-tx-all-paths
Configure BGP to send all known paths to neighbor in order to preserve multi path capabilities inside a network.
- neighbor <A.B.C.D|X:X::X:X|WORD> addpath-tx-bestpath-per-AS
Configure BGP to send best known paths to neighbor in order to preserve multi path capabilities inside a network.
- neighbor <A.B.C.D|X:X::X:X|WORD> disable-addpath-rx
Do not accept additional paths from this neighbor.
- neighbor PEER ttl-security hops NUMBER
This command enforces Generalized TTL Security Mechanism (GTSM), as specified in RFC 5082. With this command, only neighbors that are the specified number of hops away will be allowed to become neighbors. This command is mutually exclusive with ebgp-multihop.
- neighbor PEER capability extended-nexthop
Allow bgp to negotiate the extended-nexthop capability with it’s peer. If you are peering over a v6 LL address then this capability is turned on automatically. If you are peering over a v6 Global Address then turning on this command will allow BGP to install v4 routes with v6 nexthops if you do not have v4 configured on interfaces.
- neighbor <A.B.C.D|X:X::X:X|WORD> accept-own
Enable handling of self-originated VPN routes containing
accept-own
community.This feature allows you to handle self-originated VPN routes, which a BGP speaker receives from a route-reflector. A ‘self-originated’ route is one that was originally advertised by the speaker itself. As per RFC 4271, a BGP speaker rejects advertisements that originated the speaker itself. However, the BGP ACCEPT_OWN mechanism enables a router to accept the prefixes it has advertised, when reflected from a route-reflector that modifies certain attributes of the prefix.
A special community called
accept-own
is attached to the prefix by the route-reflector, which is a signal to the receiving router to bypass the ORIGINATOR_ID and NEXTHOP/MP_REACH_NLRI check.Default: disabled.
- neighbor <A.B.C.D|X:X::X:X|WORD> path-attribute discard (1-255)...
Drops specified path attributes from BGP UPDATE messages from the specified neighbor.
If you do not want specific attributes, you can drop them using this command, and let the BGP proceed by ignoring those attributes.
- neighbor <A.B.C.D|X:X::X:X|WORD> path-attribute treat-as-withdraw (1-255)...
Received BGP UPDATES that contain specified path attributes are treat-as-withdraw. If there is an existing prefix in the BGP routing table, it will be removed.
- neighbor <A.B.C.D|X:X::X:X|WORD> graceful-shutdown
Mark all routes from this neighbor as less preferred by setting
graceful-shutdown
community, and local-preference to 0.
- bgp fast-external-failover
This command causes bgp to take down ebgp peers immediately when a link flaps. bgp fast-external-failover is the default and will not be displayed as part of a show run. The no form of the command turns off this ability.
- bgp default ipv4-unicast
This command allows the user to specify that the IPv4 Unicast address family is turned on by default or not. This command defaults to on and is not displayed. The no bgp default ipv4-unicast form of the command is displayed.
- bgp default ipv4-vpn
This command allows the user to specify that the IPv4 MPLS VPN address family is turned on by default or not. This command defaults to off and is not displayed. The bgp default ipv4-vpn form of the command is displayed.
- bgp default ipv6-unicast
This command allows the user to specify that the IPv6 Unicast address family is turned on by default or not. This command defaults to off and is not displayed. The bgp default ipv6-unicast form of the command is displayed.
- bgp default ipv6-vpn
This command allows the user to specify that the IPv6 MPLS VPN address family is turned on by default or not. This command defaults to off and is not displayed. The bgp default ipv6-vpn form of the command is displayed.
- bgp default show-hostname
This command shows the hostname of the peer in certain BGP commands outputs. It’s easier to troubleshoot if you have a number of BGP peers.
- bgp default show-nexthop-hostname
This command shows the hostname of the next-hop in certain BGP commands outputs. It’s easier to troubleshoot if you have a number of BGP peers and a number of routes to check.
- neighbor PEER advertisement-interval (0-600)
Setup the minimum route advertisement interval(mrai) for the peer in question. This number is between 0 and 600 seconds, with the default advertisement interval being 0.
- neighbor PEER timers (0-65535) (0-65535)
Set keepalive and hold timers for a neighbor. The first value is keepalive and the second is hold time.
- neighbor PEER timers connect (1-65535)
Set connect timer for a neighbor. The connect timer controls how long BGP waits between connection attempts to a neighbor.
- neighbor PEER timers delayopen (1-240)
This command allows the user enable the RFC 4271 <https://tools.ietf.org/html/rfc4271/> DelayOpenTimer with the specified interval or disable it with the negating command for the peer. By default, the DelayOpenTimer is disabled. The timer interval may be set to a duration of 1 to 240 seconds.
- bgp minimum-holdtime (1-65535)
This command allows user to prevent session establishment with BGP peers with lower holdtime less than configured minimum holdtime. When this command is not set, minimum holdtime does not work.
- bgp tcp-keepalive (1-65535) (1-65535) (1-30)
This command allows user to configure TCP keepalive with new BGP peers. Each parameter respectively stands for TCP keepalive idle timer (seconds), interval (seconds), and maximum probes. By default, TCP keepalive is disabled.
Displaying Information about Peers
- show bgp <afi> <safi> neighbors WORD bestpath-routes [detail] [json] [wide]
For the given neighbor, WORD, that is specified list the routes selected by BGP as having the best path.
If
detail
option is specified, the detailed version of all routes will be displayed. The same format asshow [ip] bgp [afi] [safi] PREFIX
will be used, but for the whole table of received, advertised or filtered prefixes.If
json
option is specified, output is displayed in JSON format.If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.
Peer Filtering
- neighbor PEER distribute-list NAME [in|out]
This command specifies a distribute-list for the peer. direct is
in
orout
.
- neighbor PEER prefix-list NAME [in|out]
- neighbor PEER filter-list NAME [in|out]
- neighbor PEER route-map NAME [in|out]
Apply a route-map on the neighbor. direct must be in or out.
- bgp route-reflector allow-outbound-policy
By default, attribute modification via route-map policy out is not reflected on reflected routes. This option allows the modifications to be reflected as well. Once enabled, it affects all reflected routes.
- neighbor PEER sender-as-path-loop-detection
Enable the detection of sender side AS path loops and filter the bad routes before they are sent.
This setting is disabled by default.
Peer Groups
Peer groups are used to help improve scaling by generating the same update information to all members of a peer group. Note that this means that the routes generated by a member of a peer group will be sent back to that originating peer with the originator identifier attribute set to indicated the originating peer. All peers not associated with a specific peer group are treated as belonging to a default peer group, and will share updates.
- neighbor WORD peer-group
This command defines a new peer group.
- neighbor PEER peer-group PGNAME
This command bind specific peer to peer group WORD.
- neighbor PEER solo
This command is used to indicate that routes advertised by the peer should not be reflected back to the peer. This command only is only meaningful when there is a single peer defined in the peer-group.
- show [ip] bgp peer-group [json]
This command displays configured BGP peer-groups.
soodar# show bgp peer-group BGP peer-group test1, remote AS 65001 Peer-group type is external Configured address-families: IPv4 Unicast; IPv6 Unicast; 1 IPv4 listen range(s) 192.168.100.0/24 2 IPv6 listen range(s) 2001:db8:1::/64 2001:db8:2::/64 Peer-group members: 192.168.200.1 Active 2001:db8::1 Active BGP peer-group test2 Peer-group type is external Configured address-families: IPv4 Unicast;
Optional
json
parameter is used to display JSON output.{ "test1":{ "remoteAs":65001, "type":"external", "addressFamiliesConfigured":[ "IPv4 Unicast", "IPv6 Unicast" ], "dynamicRanges":{ "IPv4":{ "count":1, "ranges":[ "192.168.100.0\/24" ] }, "IPv6":{ "count":2, "ranges":[ "2001:db8:1::\/64", "2001:db8:2::\/64" ] } }, "members":{ "192.168.200.1":{ "status":"Active" }, "2001:db8::1":{ "status":"Active" } } }, "test2":{ "type":"external", "addressFamiliesConfigured":[ "IPv4 Unicast" ] } }
Capability Negotiation
- neighbor PEER strict-capability-match
Strictly compares remote capabilities and local capabilities. If capabilities are different, send Unsupported Capability error then reset connection.
You may want to disable sending Capability Negotiation OPEN message optional parameter to the peer when remote peer does not implement Capability Negotiation. Please use dont-capability-negotiate command to disable the feature.
- neighbor PEER dont-capability-negotiate
Suppress sending Capability Negotiation as OPEN message optional parameter to the peer. This command only affects the peer is configured other than IPv4 unicast configuration.
When remote peer does not have capability negotiation feature, remote peer will not send any capabilities at all. In that case, bgp configures the peer with configured capabilities.
You may prefer locally configured capabilities more than the negotiated capabilities even though remote peer sends capabilities. If the peer is configured by override-capability, bgpd ignores received capabilities then override negotiated capabilities with configured values.
Additionally the operator should be reminded that this feature fundamentally disables the ability to use widely deployed BGP features. BGP unnumbered, hostname support, AS4, Addpath, Route Refresh, ORF, Dynamic Capabilities, and graceful restart.
- neighbor PEER override-capability
Override the result of Capability Negotiation with local configuration. Ignore remote peer’s capability value.
- neighbor PEER capability software-version
Send the software version in the BGP OPEN message to the neighbor. This is very useful in environments with a large amount of peers with different versions of FRR or any other vendor.
Disabled by default.
- neighbor PEER aigp
Send and receive AIGP attribute for this neighbor. This is valid only for eBGP neighbors.
Disabled by default. iBGP neighbors have this option enabled implicitly.
AS Path Access Lists
AS path access list is user defined AS path.
- bgp as-path access-list WORD [seq (0-4294967295)] permit|deny LINE
This command defines a new AS path access list.
- show bgp as-path-access-list [json]
Display all BGP AS Path access lists.
If the
json
option is specified, output is displayed in JSON format.
- show bgp as-path-access-list WORD [json]
Display the specified BGP AS Path access list.
If the
json
option is specified, output is displayed in JSON format.
Bogon ASN filter policy configuration example
bgp as-path access-list 99 permit _0_
bgp as-path access-list 99 permit _23456_
bgp as-path access-list 99 permit _1310[0-6][0-9]_|_13107[0-1]_
bgp as-path access-list 99 seq 20 permit ^65
Using AS Path in Route Map
- match as-path WORD
For a given as-path, WORD, match it on the BGP as-path given for the prefix and if it matches do normal route-map actions. The no form of the command removes this match from the route-map.
- set as-path prepend AS-PATH
Prepend the given string of AS numbers to the AS_PATH of the BGP path’s NLRI. The no form of this command removes this set operation from the route-map.
- set as-path prepend last-as NUM
Prepend the existing last AS number (the leftmost ASN) to the AS_PATH. The no form of this command removes this set operation from the route-map.
- set as-path replace <any|ASN>
Replace a specific AS number to local AS number.
any
replaces each AS number in the AS-PATH with the local AS number.
Communities Attribute
The BGP communities attribute is widely used for implementing policy routing. Network operators can manipulate BGP communities attribute based on their network policy. BGP communities attribute is defined in RFC 1997 and RFC 1998. It is an optional transitive attribute, therefore local policy can travel through different autonomous system.
The communities attribute is a set of communities values. Each community value is 4 octet long. The following format is used to define the community value.
AS:VAL
This format represents 4 octet communities value.
AS
is high order 2 octet in digit format.VAL
is low order 2 octet in digit format. This format is useful to define AS oriented policy value. For example,7675:80
can be used when AS 7675 wants to pass local policy value 80 to neighboring peer.graceful-shutdown
graceful-shutdown
represents well-known communities valueGRACEFUL_SHUTDOWN
0xFFFF0000
65535:0
. RFC 8326 implements the purpose Graceful BGP Session Shutdown to reduce the amount of lost traffic when taking BGP sessions down for maintenance. The use of the community needs to be supported from your peers side to actually have any effect.accept-own
accept-own
represents well-known communities valueACCEPT_OWN
0xFFFF0001
65535:1
. RFC 7611 implements a way to signal to a router to accept routes with a local nexthop address. This can be the case when doing policing and having traffic having a nexthop located in another VRF but still local interface to the router. It is recommended to read the RFC for full details.route-filter-translated-v4
route-filter-translated-v4
represents well-known communities valueROUTE_FILTER_TRANSLATED_v4
0xFFFF0002
65535:2
.route-filter-v4
route-filter-v4
represents well-known communities valueROUTE_FILTER_v4
0xFFFF0003
65535:3
.route-filter-translated-v6
route-filter-translated-v6
represents well-known communities valueROUTE_FILTER_TRANSLATED_v6
0xFFFF0004
65535:4
.route-filter-v6
route-filter-v6
represents well-known communities valueROUTE_FILTER_v6
0xFFFF0005
65535:5
.llgr-stale
llgr-stale
represents well-known communities valueLLGR_STALE
0xFFFF0006
65535:6
. Assigned and intended only for use with routers supporting the Long-lived Graceful Restart Capability as described in [Draft-IETF-uttaro-idr-bgp-persistence]. Routers receiving routes with this community may (depending on implementation) choose allow to reject or modify routes on the presence or absence of this community.no-llgr
no-llgr
represents well-known communities valueNO_LLGR
0xFFFF0007
65535:7
. Assigned and intended only for use with routers supporting the Long-lived Graceful Restart Capability as described in [Draft-IETF-uttaro-idr-bgp-persistence]. Routers receiving routes with this community may (depending on implementation) choose allow to reject or modify routes on the presence or absence of this community.accept-own-nexthop
accept-own-nexthop
represents well-known communities valueaccept-own-nexthop
0xFFFF0008
65535:8
. [Draft-IETF-agrewal-idr-accept-own-nexthop] describes how to tag and label VPN routes to be able to send traffic between VRFs via an internal layer 2 domain on the same PE device. Refer to [Draft-IETF-agrewal-idr-accept-own-nexthop] for full details.blackhole
blackhole
represents well-known communities valueBLACKHOLE
0xFFFF029A
65535:666
. RFC 7999 documents sending prefixes to EBGP peers and upstream for the purpose of blackholing traffic. Prefixes tagged with the this community should normally not be re-advertised from neighbors of the originating network. Upon receivingBLACKHOLE
community from a BGP speaker,NO_ADVERTISE
community is added automatically.no-export
no-export
represents well-known communities valueNO_EXPORT
0xFFFFFF01
. All routes carry this value must not be advertised to outside a BGP confederation boundary. If neighboring BGP peer is part of BGP confederation, the peer is considered as inside a BGP confederation boundary, so the route will be announced to the peer.no-advertise
no-advertise
represents well-known communities valueNO_ADVERTISE
0xFFFFFF02
. All routes carry this value must not be advertise to other BGP peers.local-AS
local-AS
represents well-known communities valueNO_EXPORT_SUBCONFED
0xFFFFFF03
. All routes carry this value must not be advertised to external BGP peers. Even if the neighboring router is part of confederation, it is considered as external BGP peer, so the route will not be announced to the peer.no-peer
no-peer
represents well-known communities valueNOPEER
0xFFFFFF04
65535:65284
. RFC 3765 is used to communicate to another network how the originating network want the prefix propagated.
When the communities attribute is received duplicate community values in the attribute are ignored and value is sorted in numerical order.
<https://tools.ietf.org/id/draft-uttaro-idr-bgp-persistence-04.txt>
<https://tools.ietf.org/id/draft-agrewal-idr-accept-own-nexthop-00.txt>
Community Lists
Community lists are user defined lists of community attribute values. These lists can be used for matching or manipulating the communities attribute in UPDATE messages.
There are two types of community list:
- standard
This type accepts an explicit value for the attribute.
- expanded
This type accepts a regular expression. Because the regex must be interpreted on each use expanded community lists are slower than standard lists.
- bgp community-list standard NAME permit|deny COMMUNITY
This command defines a new standard community list.
COMMUNITY
is communities value. TheCOMMUNITY
is compiled into community structure. We can define multiple community list under same name. In that case match will happen user defined order. Once the community list matches to communities attribute in BGP updates it return permit or deny by the community list definition. When there is no matched entry, deny will be returned. WhenCOMMUNITY
is empty it matches to any routes.
- bgp community-list expanded NAME permit|deny COMMUNITY
This command defines a new expanded community list.
COMMUNITY
is a string expression of communities attribute.COMMUNITY
can be a regular expression (BGP Regular Expressions) to match the communities attribute in BGP updates. The expanded community is only used to filter, not set actions.
Deprecated since version 5.0: It is recommended to use the more explicit versions of this command.
- bgp community-list NAME permit|deny COMMUNITY
When the community list type is not specified, the community list type is automatically detected. If
COMMUNITY
can be compiled into communities attribute, the community list is defined as a standard community list. Otherwise it is defined as an expanded community list. This feature is left for backward compatibility. Use of this feature is not recommended.Note that all community lists share the same namespace, so it’s not necessary to specify
standard
orexpanded
; these modifiers are purely aesthetic.
- show bgp community-list [NAME detail]
Displays community list information. When
NAME
is specified the specified community list’s information is shown.# show bgp community-list Named Community standard list CLIST permit 7675:80 7675:100 no-export deny internet Named Community expanded list EXPAND permit : # show bgp community-list CLIST detail Named Community standard list CLIST permit 7675:80 7675:100 no-export deny internet
Numbered Community Lists
When number is used for BGP community list name, the number has special meanings. Community list number in the range from 1 to 99 is standard community list. Community list number in the range from 100 to 500 is expanded community list. These community lists are called as numbered community lists. On the other hand normal community lists is called as named community lists.
- bgp community-list (1-99) permit|deny COMMUNITY
This command defines a new community list. The argument to (1-99) defines the list identifier.
- bgp community-list (100-500) permit|deny COMMUNITY
This command defines a new expanded community list. The argument to (100-500) defines the list identifier.
Community alias
BGP community aliases are useful to quickly identify what communities are set for a specific prefix in a human-readable format. Especially handy for a huge amount of communities. Accurately defined aliases can help you faster spot things on the wire.
- bgp community alias NAME ALIAS
This command creates an alias name for a community that will be used later in various CLI outputs in a human-readable format.
soodar# show run | include bgp community alias bgp community alias 65001:14 community-1 bgp community alias 65001:123:1 lcommunity-1 soodar# show ip bgp 172.16.16.1/32 BGP routing table entry for 172.16.16.1/32, version 21 Paths: (2 available, best #2, table default) Advertised to non peer-group peers: 65030 192.168.0.2 from 192.168.0.2 (172.16.16.1) Origin incomplete, metric 0, valid, external, best (Neighbor IP) Community: 65001:12 65001:13 community-1 65001:65534 Large Community: lcommunity-1 65001:123:2 Last update: Fri Apr 16 12:51:27 2021
- show bgp [afi] [safi] [all] alias WORD [wide|json]
Display prefixes with matching BGP community alias.
Using Communities in Route Maps
In Route Maps we can match on or set the BGP communities attribute. Using this feature network operator can implement their network policy based on BGP communities attribute.
The following commands can be used in route maps:
- match alias WORD
This command performs match to BGP updates using community alias WORD. When the one of BGP communities value match to the one of community alias value in community alias, it is match.
- match community WORD exact-match [exact-match]
This command perform match to BGP updates using community list WORD. When the one of BGP communities value match to the one of communities value in community list, it is match. When exact-match keyword is specified, match happen only when BGP updates have completely same communities value specified in the community list.
- set community <none|COMMUNITY> additive
This command sets the community value in BGP updates. If the attribute is already configured, the newly provided value replaces the old one unless the
additive
keyword is specified, in which case the new value is appended to the existing value.If
none
is specified as the community value, the communities attribute is not sent.It is not possible to set an expanded community list.
- set comm-list WORD delete
This command remove communities value from BGP communities attribute. The
word
is community list name. When BGP route’s communities value matches to the community listword
, the communities value is removed. When all of communities value is removed eventually, the BGP update’s communities attribute is completely removed.
Example Configuration
The following configuration is exemplary of the most typical usage of BGP communities attribute. In the example, AS 7675 provides an upstream Internet connection to AS 100. When the following configuration exists in AS 7675, the network operator of AS 100 can set local preference in AS 7675 network by setting BGP communities attribute to the updates.
router bgp 7675
neighbor 192.168.0.1 remote-as 100
address-family ipv4 unicast
neighbor 192.168.0.1 route-map RMAP in
exit-address-family
!
bgp community-list 70 permit 7675:70
bgp community-list 80 permit 7675:80
bgp community-list 90 permit 7675:90
!
route-map RMAP permit 10
match community 70
set local-preference 70
!
route-map RMAP permit 20
match community 80
set local-preference 80
!
route-map RMAP permit 30
match community 90
set local-preference 90
The following configuration announces 10.0.0.0/8
from AS 100 to AS 7675.
The route has communities value 7675:80
so when above configuration exists
in AS 7675, the announced routes’ local preference value will be set to 80.
router bgp 100
network 10.0.0.0/8
neighbor 192.168.0.2 remote-as 7675
address-family ipv4 unicast
neighbor 192.168.0.2 route-map RMAP out
exit-address-family
!
ip prefix-list PLIST permit 10.0.0.0/8
!
route-map RMAP permit 10
match ip address prefix-list PLIST
set community 7675:80
The following configuration is an example of BGP route filtering using
communities attribute. This configuration only permit BGP routes which has BGP
communities value (0:80
and 0:90
) or 0:100
. The network operator can
set special internal communities value at BGP border router, then limit the
BGP route announcements into the internal network.
router bgp 7675
neighbor 192.168.0.1 remote-as 100
address-family ipv4 unicast
neighbor 192.168.0.1 route-map RMAP in
exit-address-family
!
bgp community-list 1 permit 0:80 0:90
bgp community-list 1 permit 0:100
!
route-map RMAP permit in
match community 1
The following example filters BGP routes which have a community value of
1:1
. When there is no match community-list returns deny
. To avoid
filtering all routes, a permit
line is set at the end of the
community-list.
router bgp 7675
neighbor 192.168.0.1 remote-as 100
address-family ipv4 unicast
neighbor 192.168.0.1 route-map RMAP in
exit-address-family
!
bgp community-list standard FILTER deny 1:1
bgp community-list standard FILTER permit
!
route-map RMAP permit 10
match community FILTER
The following configuration is an example of communities value deletion. With
this configuration the community values 100:1
and 100:2
are removed
from BGP updates. For communities value deletion, only permit
community-list is used. deny
community-list is ignored.
router bgp 7675
neighbor 192.168.0.1 remote-as 100
address-family ipv4 unicast
neighbor 192.168.0.1 route-map RMAP in
exit-address-family
!
bgp community-list standard DEL permit 100:1 100:2
!
route-map RMAP permit 10
set comm-list DEL delete
Extended Communities Attribute
BGP extended communities attribute is introduced with MPLS VPN/BGP technology. MPLS VPN/BGP expands capability of network infrastructure to provide VPN functionality. At the same time it requires a new framework for policy routing. With BGP Extended Communities Attribute we can use Route Target or Site of Origin for implementing network policy for MPLS VPN/BGP.
BGP Extended Communities Attribute is similar to BGP Communities Attribute. It is an optional transitive attribute. BGP Extended Communities Attribute can carry multiple Extended Community value. Each Extended Community value is eight octet length.
BGP Extended Communities Attribute provides an extended range compared with BGP Communities Attribute. Adding to that there is a type field in each value to provides community space structure.
There are two format to define Extended Community value. One is AS based format the other is IP address based format.
AS:VAL
This is a format to define AS based Extended Community value.
AS
part is 2 octets Global Administrator subfield in Extended Community value.VAL
part is 4 octets Local Administrator subfield.7675:100
represents AS 7675 policy value 100.IP-Address:VAL
This is a format to define IP address based Extended Community value.
IP-Address
part is 4 octets Global Administrator subfield.VAL
part is 2 octets Local Administrator subfield.
Extended Community Lists
- bgp extcommunity-list standard NAME permit|deny EXTCOMMUNITY
This command defines a new standard extcommunity-list. extcommunity is extended communities value. The extcommunity is compiled into extended community structure. We can define multiple extcommunity-list under same name. In that case match will happen user defined order. Once the extcommunity-list matches to extended communities attribute in BGP updates it return permit or deny based upon the extcommunity-list definition. When there is no matched entry, deny will be returned. When extcommunity is empty it matches to any routes.
- bgp extcommunity-list expanded NAME permit|deny LINE
This command defines a new expanded extcommunity-list. line is a string expression of extended communities attribute. line can be a regular expression (BGP Regular Expressions) to match an extended communities attribute in BGP updates.
Note that all extended community lists shares a single name space, so it’s not necessary to specify their type when creating or destroying them.
- show bgp extcommunity-list [NAME detail]
This command displays current extcommunity-list information. When name is specified the community list’s information is shown.
BGP Extended Communities in Route Map
- match extcommunity WORD
- set extcommunity none
This command resets the extended community value in BGP updates. If the attribute is already configured or received from the peer, the attribute is discarded and set to none. This is useful if you need to strip incoming extended communities.
- set extcommunity rt EXTCOMMUNITY
This command sets Route Target value.
- set extcommunity nt EXTCOMMUNITY
This command sets Node Target value.
If the receiving BGP router supports Node Target Extended Communities, it will install the route with the community that contains it’s own local BGP Identifier. Otherwise, it’s not installed.
- set extcommunity soo EXTCOMMUNITY
This command sets Site of Origin value.
- set extcommunity bandwidth <(1-25600) | cumulative | num-multipaths> [non-transitive]
This command sets the BGP link-bandwidth extended community for the prefix (best path) for which it is applied. The link-bandwidth can be specified as an
explicit value
(specified in Mbps), or the router can be told to use thecumulative bandwidth
of all multipaths for the prefix or to compute it based on thenumber of multipaths
. The link bandwidth extended community is encoded astransitive
unless the set command explicitly configures it asnon-transitive
.
Note that the extended expanded community is only used for match rule, not for set actions.
Large Communities Attribute
The BGP Large Communities attribute was introduced in Feb 2017 with RFC 8092.
The BGP Large Communities Attribute is similar to the BGP Communities Attribute
except that it has 3 components instead of two and each of which are 4 octets
in length. Large Communities bring additional functionality and convenience
over traditional communities, specifically the fact that the GLOBAL
part
below is now 4 octets wide allowing seamless use in networks using 4-byte ASNs.
GLOBAL:LOCAL1:LOCAL2
This is the format to define Large Community values. Referencing RFC 8195 the values are commonly referred to as follows:
The
GLOBAL
part is a 4 octet Global Administrator field, commonly used as the operators AS number.The
LOCAL1
part is a 4 octet Local Data Part 1 subfield referred to as a function.The
LOCAL2
part is a 4 octet Local Data Part 2 field and referred to as the parameter subfield.
As an example,
65551:1:10
represents AS 65551 function 1 and parameter 10. The referenced RFC above gives some guidelines on recommended usage.
Large Community Lists
Two types of large community lists are supported, namely standard and expanded.
- bgp large-community-list standard NAME permit|deny LARGE-COMMUNITY
This command defines a new standard large-community-list. large-community is the Large Community value. We can add multiple large communities under same name. In that case the match will happen in the user defined order. Once the large-community-list matches the Large Communities attribute in BGP updates it will return permit or deny based upon the large-community-list definition. When there is no matched entry, a deny will be returned. When large-community is empty it matches any routes.
- bgp large-community-list expanded NAME permit|deny LINE
This command defines a new expanded large-community-list. Where line is a string matching expression, it will be compared to the entire Large Communities attribute as a string, with each large-community in order from lowest to highest. line can also be a regular expression which matches this Large Community attribute.
Note that all community lists share the same namespace, so it’s not necessary to specify
standard
orexpanded
; these modifiers are purely aesthetic.
- show bgp large-community-list
- show bgp large-community-list NAME detail
This command display current large-community-list information. When name is specified the community list information is shown.
- show ip bgp large-community-info
This command displays the current large communities in use.
Large Communities in Route Map
- match large-community LINE [exact-match]
Where line can be a simple string to match, or a regular expression. It is very important to note that this match occurs on the entire large-community string as a whole, where each large-community is ordered from lowest to highest. When exact-match keyword is specified, match happen only when BGP updates have completely same large communities value specified in the large community list.
- set large-community LARGE-COMMUNITY
- set large-community LARGE-COMMUNITY LARGE-COMMUNITY
- set large-community LARGE-COMMUNITY additive
These commands are used for setting large-community values. The first command will overwrite any large-communities currently present. The second specifies two large-communities, which overwrites the current large-community list. The third will add a large-community value without overwriting other values. Multiple large-community values can be specified.
Note that the large expanded community is only used for match rule, not for set actions.
BGP Roles and Only to Customers
BGP roles are defined in RFC 9234 and provide an easy way to route leaks prevention, detection and mitigation.
To enable its mechanics, you must set your local role to reflect your type of
peering relationship with your neighbor. Possible values of LOCAL-ROLE
are:
provider
rs-server
rs-client
customer
peer
The local Role value is negotiated with the new BGP Role capability with a built-in check of the corresponding value. In case of mismatch the new OPEN Roles Mismatch Notification <2, 11> would be sent.
The correct Role pairs are:
Provider - Customer
Peer - Peer
RS-Server - RS-Client
soodar# show bgp neighbor | include Role
Local Role: customer
Neighbor Role: provider
Role: advertised and received
If strict-mode is set BGP session won’t become established until BGP neighbor set local Role on its side. This configuration parameter is defined in RFC 9234 and used to enforce corresponding configuration at your counter-part side. Default value - disabled.
Routes that sent from provider, rs-server, or peer local-role (or if received by customer, rs-clinet, or peer local-role) will be marked with a new Only to Customer (OTC) attribute.
Routes with this attribute can only be sent to your neighbor if your local-role is provider or rs-server. Routes with this attribute can be received only if your local-role is customer or rs-client.
In case of peer-peer relationship routes can be received only if OTC value is equal to your neighbor AS number.
All these rules with OTC help to detect and mitigate route leaks and happened automatically if local-role is set.
- neighbor PEER local-role LOCAL-ROLE [strict-mode]
This command set your local-role to
LOCAL-ROLE
: <provider|rs-server|rs-client|customer|peer>.This role helps to detect and prevent route leaks.
If
strict-mode
is set, your neighbor must send you Capability with the value of his role (by setting local-role on his side). Otherwise, a Role Mismatch Notification will be sent.
Labeled unicast
bgpd supports labeled information, as per RFC 3107.
By default, locally advertised prefixes use the implicit-null label to encode in the outgoing NLRI. The following command uses the explicit-null label value for all the BGP instances.
L3VPN VRFs
bgpd supports L3VPN VRFs for IPv4 RFC 4364 and IPv6 RFC 4659. L3VPN routes, and their associated VRF MPLS labels, can be distributed to VPN SAFI neighbors in the default, i.e., non VRF, BGP instance. VRF MPLS labels are reached using core MPLS labels which are distributed using LDP or BGP labeled unicast. bgpd also supports inter-VRF route leaking.
VRF Route Leaking
BGP routes may be leaked (i.e. copied) between a unicast VRF RIB and the VPN
SAFI RIB of the default VRF for use in MPLS-based L3VPNs. Unicast routes may
also be leaked between any VRFs (including the unicast RIB of the default BGP
instanced). A shortcut syntax is also available for specifying leaking from one
VRF to another VRF using the default instance’s VPN RIB as the intermediary. A
common application of the VRF-VRF feature is to connect a customer’s private
routing domain to a provider’s VPN service. Leaking is configured from the
point of view of an individual VRF: import
refers to routes leaked from VPN
to a unicast VRF, whereas export
refers to routes leaked from a unicast VRF
to VPN.
Required parameters
Routes exported from a unicast VRF to the VPN RIB must be augmented by two parameters:
an RD
an RTLIST
Configuration for these exported routes must, at a minimum, specify these two parameters.
Routes imported from the VPN RIB to a unicast VRF are selected according to their RTLISTs. Routes whose RTLIST contains at least one route-target in common with the configured import RTLIST are leaked. Configuration for these imported routes must specify an RTLIST to be matched.
The RD, which carries no semantic value, is intended to make the route unique in the VPN RIB among all routes of its prefix that originate from all the customers and sites that are attached to the provider’s VPN service. Accordingly, each site of each customer is typically assigned an RD that is unique across the entire provider network.
The RTLIST is a set of route-target extended community values whose purpose is to specify route-leaking policy. Typically, a customer is assigned a single route-target value for import and export to be used at all customer sites. This configuration specifies a simple topology wherein a customer has a single routing domain which is shared across all its sites. More complex routing topologies are possible through use of additional route-targets to augment the leaking of sets of routes in various ways.
When using the shortcut syntax for vrf-to-vrf leaking, the RD and RT are auto-derived.
General configuration
Configuration of route leaking between a unicast VRF RIB and the VPN SAFI RIB of the default VRF is accomplished via commands in the context of a VRF address-family:
- rd vpn export AS:NN|IP:nn
Specifies the route distinguisher to be added to a route exported from the current unicast VRF to VPN.
- rt vpn import|export|both RTLIST...
Specifies the route-target list to be attached to a route (export) or the route-target list to match against (import) when exporting/importing between the current unicast VRF and VPN.
The RTLIST is a space-separated list of route-targets, which are BGP extended community values as described in Extended Communities Attribute.
- label vpn export allocation-mode per-vrf|per-nexthop
Select how labels are allocated in the given VRF. By default, the per-vrf mode is selected, and one label is used for all prefixes from the VRF. The per-nexthop will use a unique label for all prefixes that are reachable via the same nexthop.
- label vpn export (0..1048575)|auto
Enables an MPLS label to be attached to a route exported from the current unicast VRF to VPN. If the value specified is
auto
, the label value is automatically assigned from a pool maintained by the Zebra daemon. If Zebra is not running, or if this command is not configured, automatic label assignment will not complete, which will block corresponding route export.
- nexthop vpn export A.B.C.D|X:X::X:X
Specifies an optional nexthop value to be assigned to a route exported from the current unicast VRF to VPN. If left unspecified, the nexthop will be set to 0.0.0.0 or 0:0::0:0 (self).
- route-map vpn import|export MAP
Specifies an optional route-map to be applied to routes imported or exported between the current unicast VRF and VPN.
- import|export vpn
Enables import or export of routes between the current unicast VRF and VPN.
- import vrf VRFNAME
Shortcut syntax for specifying automatic leaking from vrf VRFNAME to the current VRF using the VPN RIB as intermediary. The RD and RT are auto derived and should not be specified explicitly for either the source or destination VRF’s.
This shortcut syntax mode is not compatible with the explicit import vpn and export vpn statements for the two VRF’s involved. The CLI will disallow attempts to configure incompatible leaking modes.
- bgp retain route-target all
It is possible to retain or not VPN prefixes that are not imported by local VRF configuration. This can be done via the following command in the context of the global VPNv4/VPNv6 family. This command defaults to on and is not displayed. The no bgp retain route-target all form of the command is displayed.
- neighbor <A.B.C.D|X:X::X:X|WORD> soo EXTCOMMUNITY
Without this command, SoO extended community attribute is configured using an inbound route map that sets the SoO value during the update process. With the introduction of the new BGP per-neighbor Site-of-Origin (SoO) feature, two new commands configured in sub-modes under router configuration mode simplify the SoO value configuration.
If we configure SoO per neighbor at PEs, the SoO community is automatically
added for all routes from the CPEs. Routes are validated and prevented from
being sent back to the same CPE (e.g.: multi-site). This is especially needed
when using as-override
or allowas-in
to prevent routing loops.
- mpls bgp forwarding
It is possible to permit BGP install VPN prefixes without transport labels, by issuing the following command under the interface configuration context. This configuration will install VPN prefixes originated from an e-bgp session, and with the next-hop directly connected.
Debugging
- show debug
Show all enabled debugs.
- show bgp listeners
Display Listen sockets and the vrf that created them. Useful for debugging of when listen is not working and this is considered a developer debug statement.
- debug bgp allow-martian
Enable or disable BGP accepting martian nexthops from a peer. Please note this is not an actual debug command and this command is also being deprecated and will be removed soon. The new command is
bgp allow-martian-nexthop
- debug bgp bfd
Enable or disable debugging for BFD events. This will show BFD integration library messages and BGP BFD integration messages that are mostly state transitions and validation problems.
- debug bgp conditional-advertisement
Enable or disable debugging of BGP conditional advertisement.
- debug bgp neighbor-events
Enable or disable debugging for neighbor events. This provides general information on BGP events such as peer connection / disconnection, session establishment / teardown, and capability negotiation.
- debug bgp updates
Enable or disable debugging for BGP updates. This provides information on BGP UPDATE messages transmitted and received between local and remote instances.
- debug bgp keepalives
Enable or disable debugging for BGP keepalives. This provides information on BGP KEEPALIVE messages transmitted and received between local and remote instances.
- debug bgp bestpath <A.B.C.D/M|X:X::X:X/M>
Enable or disable debugging for bestpath selection on the specified prefix.
- debug bgp nht
Enable or disable debugging of BGP nexthop tracking.
- debug bgp update-groups
Enable or disable debugging of dynamic update groups. This provides general information on group creation, deletion, join and prune events.
- debug bgp zebra
Enable or disable debugging of communications between bgpd and zebra.
Other BGP Commands
The following are available in the top level enable mode:
- clear bgp \*
Clear all peers.
- clear bgp ipv4|ipv6 \*
Clear all peers with this address-family activated.
- clear bgp ipv4|ipv6 unicast \*
Clear all peers with this address-family and sub-address-family activated.
- clear bgp ipv4|ipv6 PEER
Clear peers with address of X.X.X.X and this address-family activated.
- clear bgp ipv4|ipv6 unicast PEER
Clear peer with address of X.X.X.X and this address-family and sub-address-family activated.
- clear bgp ipv4|ipv6 PEER soft|in|out
Clear peer using soft reconfiguration in this address-family.
- clear bgp ipv4|ipv6 unicast PEER soft|in|out
Clear peer using soft reconfiguration in this address-family and sub-address-family.
- clear bgp [ipv4|ipv6] [unicast] PEER|\* message-stats
Clear BGP message statistics for a specified peer or for all peers, optionally filtered by activated address-family and sub-address-family.
The following are available in the router bgp
mode:
- write-quanta (1-64)
BGP message Tx I/O is vectored. This means that multiple packets are written to the peer socket at the same time each I/O cycle, in order to minimize system call overhead. This value controls how many are written at a time. Under certain load conditions, reducing this value could make peer traffic less ‘bursty’. In practice, leave this settings on the default (64) unless you truly know what you are doing.
- read-quanta (1-10)
Unlike Tx, BGP Rx traffic is not vectored. Packets are read off the wire one at a time in a loop. This setting controls how many iterations the loop runs for. As with write-quanta, it is best to leave this setting on the default.
The following command is available in config
mode as well as in the
router bgp
mode:
- bgp graceful-shutdown
The purpose of this command is to initiate BGP Graceful Shutdown which is described in RFC 8326. The use case for this is to minimize or eliminate the amount of traffic loss in a network when a planned maintenance activity such as software upgrade or hardware replacement is to be performed on a router. The feature works by re-announcing routes to eBGP peers with the GRACEFUL_SHUTDOWN community included. Peers are then expected to treat such paths with the lowest preference. This happens automatically on a receiver running FRR; with other routing protocol stacks, an inbound policy may have to be configured. In FRR, triggering graceful shutdown also results in announcing a LOCAL_PREF of 0 to iBGP peers.
Graceful shutdown can be configured per BGP instance or globally for all of BGP. These two options are mutually exclusive. The no form of the command causes graceful shutdown to be stopped, and routes will be re-announced without the GRACEFUL_SHUTDOWN community and/or with the usual LOCAL_PREF value. Note that if this option is saved to the startup configuration, graceful shutdown will remain in effect across restarts of bgpd and will need to be explicitly disabled.
- bgp input-queue-limit (1-4294967295)
Set the BGP Input Queue limit for all peers when messaging parsing. Increase this only if you have the memory to handle large queues of messages at once.
- bgp output-queue-limit (1-4294967295)
Set the BGP Output Queue limit for all peers when messaging parsing. Increase this only if you have the memory to handle large queues of messages at once.
Displaying BGP Information
The following four commands display the IPv6 and IPv4 routing tables, depending
on whether or not the ip
keyword is used.
Actually, show ip bgp
command was used on older Quagga routing
daemon project, while show bgp
command is the new format. The choice
has been done to keep old format with IPv4 routing table, while new format
displays IPv6 routing table.
- show ip bgp [all] [wide|json [detail]]
- show ip bgp A.B.C.D [json]
- show bgp [all] [wide|json [detail]]
- show bgp X:X::X:X [json]
These commands display BGP routes. When no route is specified, the default is to display all BGP routes.
BGP table version is 0, local router ID is 10.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path \*> 1.1.1.1/32 0.0.0.0 0 32768 i Total number of prefixes 1
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.This is especially handy dealing with IPv6 prefixes and if
[no] bgp default show-nexthop-hostname
is enabled.If
all
option is specified,ip
keyword is ignored, show bgp all and show ip bgp all commands display routes for all AFIs and SAFIs.If
json
option is specified, output is displayed in JSON format.If
detail
option is specified afterjson
, more verbose JSON output will be displayed.
Some other commands provide additional options for filtering the output.
- show [ip] bgp regexp LINE
This command displays BGP routes using AS path regular expression (BGP Regular Expressions).
- show [ip] bgp [all] summary [wide] [json]
Show a bgp peer summary for the specified address family.
The old command structure show ip bgp
may be removed in the future
and should no longer be used. In order to reach the other BGP routing tables
other than the IPv6 routing table given by show bgp
, the new command
structure is extended with show bgp [afi] [safi]
.
wide
option gives more output like LocalAS
and extended Desc
to
64 characters.
soodar# show ip bgp summary wide IPv4 Unicast Summary (VRF default): BGP router identifier 192.168.100.1, local AS number 65534 vrf-id 0 BGP table version 3 RIB entries 5, using 920 bytes of memory Peers 1, using 27 KiB of memory Neighbor V AS LocalAS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc 192.168.0.2 4 65030 123 15 22 0 0 0 00:07:00 0 1 us-east1-rs1.frrouting.org Total number of neighbors 1 soodar#
If PfxRcd and/or PfxSnt is shown as (Policy)
, that means that the EBGP
default policy is turned on, but you don’t have any filters applied for
incoming/outgoing directions.
See also
- show bgp vrfs [<VRFNAME$vrf_name>] [json]
The command displays all bgp vrf instances basic info like router-id, configured and established neighbors, evpn related basic info like l3vni, router-mac, vxlan-interface. User can get that information as JSON format when
json
keyword at the end of cli is presented.soodar# show bgp vrfs Type Id routerId #PeersCfg #PeersEstb Name L3-VNI RouterMAC Interface DFLT 0 17.0.0.6 3 3 default 0 00:00:00:00:00:00 unknown VRF 21 17.0.0.6 0 0 sym_1 8888 34:11:12:22:22:01 vlan4034_l3 VRF 32 17.0.0.6 0 0 sym_2 8889 34:11:12:22:22:01 vlan4035_l3 Total number of VRFs (including default): 3
- show bgp [afi] [safi] [all] [wide|json]
- show bgp [<ipv4|ipv6> <unicast|vpn|labeled-unicast>]
These commands display BGP routes for the specific routing table indicated by the selected afi and the selected safi. If no afi and no safi value is given, the command falls back to the default IPv6 routing table
- show bgp [afi] [safi] [all] summary [json]
Show a bgp peer summary for the specified address family, and subsequent address-family.
- show bgp [afi] [safi] [all] summary failed [json]
Show a bgp peer summary for peers that are not successfully exchanging routes for the specified address family, and subsequent address-family.
- show bgp [afi] [safi] [all] summary established [json]
Show a bgp peer summary for peers that are successfully exchanging routes for the specified address family, and subsequent address-family.
- show bgp [afi] [safi] [all] summary neighbor [PEER] [json]
Show a bgp summary for the specified peer, address family, and subsequent address-family. The neighbor filter can be used in combination with the failed, established filters.
- show bgp [afi] [safi] [all] summary remote-as <internal|external|ASN> [json]
Show a bgp peer summary for the specified remote-as ASN or type (
internal
for iBGP andexternal
for eBGP sessions), address family, and subsequent address-family. The remote-as filter can be used in combination with the failed, established filters.
- show bgp [afi] [safi] [all] summary terse [json]
Shorten the output. Do not show the following information about the BGP instances: the number of RIB entries, the table version and the used memory. The
terse
option can be used in combination with the remote-as, neighbor, failed and established filters, and with thewide
option as well.
- show bgp [afi] [safi] [neighbor [PEER] [routes|advertised-routes|received-routes] [<A.B.C.D/M|X:X::X:X/M> | detail] [json]
- show bgp [<view|vrf> VIEWVRFNAME] [afi] [safi] neighbors PEER received prefix-filter [json]
- show bgp [afi] [safi] [all] dampening dampened-paths [wide|json]
Display paths suppressed due to dampening of the selected afi and safi selected.
- show bgp [afi] [safi] [all] dampening flap-statistics [wide|json]
Display flap statistics of routes of the selected afi and safi selected.
- show bgp [afi] [safi] [all] dampening parameters [json]
Display details of configured dampening parameters of the selected afi and safi.
If the
json
option is specified, output is displayed in JSON format.
- show bgp [afi] [safi] [all] version (1-4294967295) [wide|json]
Display prefixes with matching version numbers. The version number and above having prefixes will be listed here.
It helps to identify which prefixes were installed at some point.
- show bgp [afi] [safi] statistics
Display statistics of routes of the selected afi and safi.
- show bgp statistics-all
Display statistics of routes of all the afi and safi.
- show [ip] bgp [afi] [safi] [all] cidr-only [wide|json]
Display routes with non-natural netmasks.
- show [ip] bgp [afi] [safi] [all] prefix-list WORD [wide|json]
Display routes that match the specified prefix-list.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.If the
json
option is specified, output is displayed in JSON format.
- show [ip] bgp [afi] [safi] [all] access-list WORD [wide|json]
Display routes that match the specified access-list.
- show [ip] bgp [afi] [safi] [all] filter-list WORD [wide|json]
Display routes that match the specified AS-Path filter-list.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.If the
json
option is specified, output is displayed in JSON format.
- show [ip] bgp [afi] [safi] [all] route-map WORD [wide|json]
Display routes that match the specified route-map.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.If the
json
option is specified, output is displayed in JSON format.
- show [ip] bgp [afi] [safi] [all] <A.B.C.D/M|X:X::X:X/M> longer-prefixes [wide|json]
Displays the specified route and all more specific routes.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.If the
json
option is specified, output is displayed in JSON format.
- show [ip] bgp [afi] [safi] [all] self-originate [wide|json]
Display self-originated routes.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.If the
json
option is specified, output is displayed in JSON format.
- show [ip] bgp [afi] [safi] [all] neighbors A.B.C.D [advertised-routes|received-routes|filtered-routes] [<A.B.C.D/M|X:X::X:X/M> | detail] [json|wide]
- show [ip] bgp [afi] [safi] [all] detail-routes
Display the detailed version of all routes. The same format as using
show [ip] bgp [afi] [safi] PREFIX
, but for the whole BGP table.If
all
option is specified,ip
keyword is ignored and, routes displayed for all AFIs and SAFIs.If
afi
is specified, withall
option, routes will be displayed for each SAFI in the selected AFI.
- show [ip] bgp [<view|vrf> VIEWVRFNAME] [afi] [safi] detail [json]
Display the detailed version of all routes from the specified bgp vrf table for a given afi + safi.
If no vrf is specified, then it is assumed as a default vrf and routes are displayed from default vrf table.
If
all
option is specified as vrf name, then all bgp vrf tables routes from a given afi+safi are displayed in the detailed output of routes.If
json
option is specified, detailed output is displayed in JSON format.Following are sample output for few examples of how to use this command.
torm-23# sh bgp ipv4 unicast detail (OR) sh bgp vrf default ipv4 unicast detail
!--- Output suppressed.
BGP routing table entry for 172.16.16.1/32
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local, (Received from a RR-client)
172.16.16.1 (metric 20) from torm-22(172.16.16.1) (192.168.0.10)
Origin IGP, metric 0, localpref 100, valid, internal
Last update: Fri May 8 12:54:05 2023
BGP routing table entry for 172.16.16.2/32
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0 from 0.0.0.0 (172.16.16.2)
Origin incomplete, metric 0, weight 32768, valid, sourced, bestpath-from-AS Local, best (First path received)
Last update: Wed May 8 12:54:41 2023
Displayed 2 routes and 2 total paths
torm-23# sh bgp vrf all detail
Instance default:
!--- Output suppressed.
BGP routing table entry for 172.16.16.1/32
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local, (Received from a RR-client)
172.16.16.1 (metric 20) from torm-22(172.16.16.1) (192.168.0.10)
Origin IGP, metric 0, localpref 100, valid, internal
Last update: Fri May 8 12:44:05 2023
BGP routing table entry for 172.16.16.2/32
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0 from 0.0.0.0 (172.16.16.2)
Origin incomplete, metric 0, weight 32768, valid, sourced, bestpath-from-AS Local, best (First path received)
Last update: Wed May 8 12:45:01 2023
Displayed 2 routes and 2 total paths
Instance vrf3:
!--- Output suppressed.
BGP routing table entry for 192.168.0.2/32
Paths: (1 available, best #1, vrf vrf3)
Not advertised to any peer
Imported from 172.16.16.1:12:[2]:[0]:[48]:[00:02:00:00:00:58]:[32]:[192.168.0.2], VNI 1008/4003
Local
172.16.16.1 from torm-22(172.16.16.1) (172.16.16.1) announce-nh-self
Origin IGP, localpref 100, valid, internal, bestpath-from-AS Local, best (First path received)
Extended Community: RT:65000:1008 ET:8 Rmac:00:02:00:00:00:58
Last update: Fri May 8 02:41:55 2023
BGP routing table entry for 192.168.1.2/32
Paths: (1 available, best #1, vrf vrf3)
Not advertised to any peer
Imported from 172.16.16.1:13:[2]:[0]:[48]:[00:02:00:00:00:58]:[32]:[192.168.1.2], VNI 1009/4003
Local
172.16.16.1 from torm-22(172.16.16.1) (172.16.16.1) announce-nh-self
Origin IGP, localpref 100, valid, internal, bestpath-from-AS Local, best (First path received)
Extended Community: RT:65000:1009 ET:8 Rmac:00:02:00:00:00:58
Last update: Fri May 8 02:41:55 2023
Displayed 2 routes and 2 total paths
torm-23# sh bgp vrf vrf3 ipv4 unicast detail
!--- Output suppressed.
BGP routing table entry for 192.168.0.2/32
Paths: (1 available, best #1, vrf vrf3)
Not advertised to any peer
Imported from 172.16.16.1:12:[2]:[0]:[48]:[00:02:00:00:00:58]:[32]:[192.168.0.2], VNI 1008/4003
Local
172.16.16.1 from torm-22(172.16.16.1) (172.16.16.1) announce-nh-self
Origin IGP, localpref 100, valid, internal, bestpath-from-AS Local, best (First path received)
Extended Community: RT:65000:1008 ET:8 Rmac:00:02:00:00:00:58
Last update: Fri May 8 02:23:35 2023
BGP routing table entry for 192.168.1.2/32
Paths: (1 available, best #1, vrf vrf3)
Not advertised to any peer
Imported from 172.16.16.1:13:[2]:[0]:[48]:[00:02:00:00:00:58]:[32]:[192.168.1.2], VNI 1009/4003
Local
172.16.16.1 from torm-22(172.16.16.1) (172.16.16.1) announce-nh-self
Origin IGP, localpref 100, valid, internal, bestpath-from-AS Local, best (First path received)
Extended Community: RT:65000:1009 ET:8 Rmac:00:02:00:00:00:58
Last update: Fri May 8 02:23:55 2023
Displayed 2 routes and 2 total paths
Displaying Routes by Community Attribute
The following commands allow displaying routes based on their community attribute.
- show [ip] bgp <ipv4|ipv6> [all] community [wide|json]
- show [ip] bgp <ipv4|ipv6> [all] community COMMUNITY [wide|json]
- show [ip] bgp <ipv4|ipv6> [all] community COMMUNITY exact-match [wide|json]
These commands display BGP routes which have the community attribute. attribute. When
COMMUNITY
is specified, BGP routes that match that community are displayed. When exact-match is specified, it display only routes that have an exact match.
- show [ip] bgp <ipv4|ipv6> community-list WORD [json]
- show [ip] bgp <ipv4|ipv6> community-list WORD exact-match [json]
These commands display BGP routes for the address family specified that match the specified community list. When exact-match is specified, it displays only routes that have an exact match.
If
wide
option is specified, then the prefix table’s width is increased to fully display the prefix and the nexthop.This is especially handy dealing with IPv6 prefixes and if
[no] bgp default show-nexthop-hostname
is enabled.If
all
option is specified,ip
keyword is ignored and, routes displayed for all AFIs and SAFIs. if afi is specified, withall
option, routes will be displayed for each SAFI in the selcted AFIIf
json
option is specified, output is displayed in JSON format.
- show bgp labelpool <chunks|inuse|ledger|requests|summary> [json]
Displaying Routes by Large Community Attribute
The following commands allow displaying routes based on their large community attribute.
- show [ip] bgp <ipv4|ipv6> large-community
- show [ip] bgp <ipv4|ipv6> large-community LARGE-COMMUNITY
- show [ip] bgp <ipv4|ipv6> large-community LARGE-COMMUNITY exact-match
- show [ip] bgp <ipv4|ipv6> large-community LARGE-COMMUNITY json
These commands display BGP routes which have the large community attribute. attribute. When
LARGE-COMMUNITY
is specified, BGP routes that match that large community are displayed. When exact-match is specified, it display only routes that have an exact match. When json is specified, it display routes in json format.
- show [ip] bgp <ipv4|ipv6> large-community-list WORD
- show [ip] bgp <ipv4|ipv6> large-community-list WORD exact-match
- show [ip] bgp <ipv4|ipv6> large-community-list WORD json
These commands display BGP routes for the address family specified that match the specified large community list. When exact-match is specified, it displays only routes that have an exact match. When json is specified, it display routes in json format.
Displaying Routes by AS Path
- show bgp ipv4|ipv6 regexp LINE
This commands displays BGP routes that matches a regular expression line (BGP Regular Expressions).
- show [ip] bgp ipv4 vpn
- show [ip] bgp ipv6 vpn
Print active IPV4 or IPV6 routes advertised via the VPN SAFI.
- show bgp ipv4 vpn summary
- show bgp ipv6 vpn summary
Print a summary of neighbor connections for the specified AFI/SAFI combination.
Displaying Routes by Route Distinguisher
- show bgp [<ipv4|ipv6> vpn [route]] rd <all|RD>
For L3VPN address-families, routes can be displayed on a per-RD (Route Distinguisher) basis or for all RD’s.
Displaying Update Group Information
- show bgp update-groups [advertise-queue|advertised-routes|packet-queue]
- show bgp update-groups statistics
Display Information about update-group events in FRR.
Displaying Nexthop Information
- show [ip] bgp [<view|vrf> VIEWVRFNAME] nexthop ipv4 [A.B.C.D] [detail] [json]
- show [ip] bgp [<view|vrf> VIEWVRFNAME] nexthop ipv6 [X:X::X:X] [detail] [json]
- show [ip] bgp [<view|vrf> VIEWVRFNAME] nexthop [<A.B.C.D|X:X::X:X>] [detail] [json]
- show [ip] bgp <view|vrf> all nexthop [json]
Display information about nexthops to bgp neighbors. If a certain nexthop is specified, also provides information about paths associated with the nexthop. With detail option provides information about gates of each nexthop.
- show [ip] bgp [<view|vrf> VIEWVRFNAME] import-check-table [detail] [json]
Display information about nexthops from table that is used to check network’s existence in the rib for network statements.
AS-notation support
By default, the ASN value output follows how the BGP ASN instance is expressed in the configuration. Three as-notation outputs are available:
plain output: both AS4B and AS2B use a single number. ` router bgp 65536`.
dot output: AS4B values are using two numbers separated by a period. router bgp 1.1 means that the AS number is 65536.
dot+ output: AS2B and AS4B values are using two numbers separated by a period. router bgp 0.5 means that the AS number is 5.
The below option permits forcing the as-notation output:
- router bgp ASN as-notation dot|dot+|plain
The chosen as-notation format will override the BGP ASN output.
Route Reflector
BGP routers connected inside the same AS through BGP belong to an internal BGP session, or IBGP. In order to prevent routing table loops, IBGP does not advertise IBGP-learned routes to other routers in the same session. As such, IBGP requires a full mesh of all peers. For large networks, this quickly becomes unscalable. Introducing route reflectors removes the need for the full-mesh.
When route reflectors are configured, these will reflect the routes announced by the peers configured as clients. A route reflector client is configured with:
- neighbor PEER route-reflector-client
To avoid single points of failure, multiple route reflectors can be configured.
A cluster is a collection of route reflectors and their clients, and is used by route reflectors to avoid looping.
- bgp cluster-id A.B.C.D
- bgp session-dscp (0-63)
This command allows bgp to control, at a global level, the TCP dscp values in the TCP header.
Routing Policy
You can set different routing policy for a peer. For example, you can set different filter for a peer.
!
router bgp 1 view 1
neighbor 10.0.0.1 remote-as 2
address-family ipv4 unicast
neighbor 10.0.0.1 distribute-list 1 in
exit-address-family
!
router bgp 1 view 2
neighbor 10.0.0.1 remote-as 2
address-family ipv4 unicast
neighbor 10.0.0.1 distribute-list 2 in
exit-address-family
This means BGP update from a peer 10.0.0.1 goes to both BGP view 1 and view 2. When the update is inserted into view 1, distribute-list 1 is applied. On the other hand, when the update is inserted into view 2, distribute-list 2 is applied.
BGP Regular Expressions
BGP regular expressions are based on POSIX 1003.2 regular expressions. The following description is just a quick subset of the POSIX regular expressions.
- .*
Matches any single character.
- *
Matches 0 or more occurrences of pattern.
- +
Matches 1 or more occurrences of pattern.
- ?
Match 0 or 1 occurrences of pattern.
- ^
Matches the beginning of the line.
- $
Matches the end of the line.
- _
The
_
character has special meanings in BGP regular expressions. It matches to space and comma , and AS set delimiter{
and}
and AS confederation delimiter(
and)
. And it also matches to the beginning of the line and the end of the line. So_
can be used for AS value boundaries match. This character technically evaluates to(^|[,{}()]|$)
.
Miscellaneous Configuration Examples
Example of a session to an upstream, advertising only one prefix to it.
router bgp 64512
bgp router-id 10.236.87.1
neighbor upstream peer-group
neighbor upstream remote-as 64515
neighbor upstream capability dynamic
neighbor 10.1.1.1 peer-group upstream
neighbor 10.1.1.1 description ACME ISP
address-family ipv4 unicast
network 10.236.87.0/24
neighbor upstream prefix-list pl-allowed-adv out
exit-address-family
!
ip prefix-list pl-allowed-adv seq 5 permit 82.195.133.0/25
ip prefix-list pl-allowed-adv seq 10 deny any
A more complex example including upstream, peer and customer sessions advertising global prefixes and NO_EXPORT prefixes and providing actions for customer routes based on community values. Extensive use is made of route-maps and the ‘call’ feature to support selective advertising of prefixes. This example is intended as guidance only, it has NOT been tested and almost certainly contains silly mistakes, if not serious flaws.
router bgp 64512
bgp router-id 10.236.87.1
neighbor upstream capability dynamic
neighbor cust capability dynamic
neighbor peer capability dynamic
neighbor 10.1.1.1 remote-as 64515
neighbor 10.1.1.1 peer-group upstream
neighbor 10.2.1.1 remote-as 64516
neighbor 10.2.1.1 peer-group upstream
neighbor 10.3.1.1 remote-as 64517
neighbor 10.3.1.1 peer-group cust-default
neighbor 10.3.1.1 description customer1
neighbor 10.4.1.1 remote-as 64518
neighbor 10.4.1.1 peer-group cust
neighbor 10.4.1.1 description customer2
neighbor 10.5.1.1 remote-as 64519
neighbor 10.5.1.1 peer-group peer
neighbor 10.5.1.1 description peer AS 1
neighbor 10.6.1.1 remote-as 64520
neighbor 10.6.1.1 peer-group peer
neighbor 10.6.1.1 description peer AS 2
address-family ipv4 unicast
network 10.123.456.0/24
network 10.123.456.128/25 route-map rm-no-export
neighbor upstream route-map rm-upstream-out out
neighbor cust route-map rm-cust-in in
neighbor cust route-map rm-cust-out out
neighbor cust send-community both
neighbor peer route-map rm-peer-in in
neighbor peer route-map rm-peer-out out
neighbor peer send-community both
neighbor 10.3.1.1 prefix-list pl-cust1-network in
neighbor 10.4.1.1 prefix-list pl-cust2-network in
neighbor 10.5.1.1 prefix-list pl-peer1-network in
neighbor 10.6.1.1 prefix-list pl-peer2-network in
exit-address-family
!
ip prefix-list pl-default permit 0.0.0.0/0
!
ip prefix-list pl-upstream-peers permit 10.1.1.1/32
ip prefix-list pl-upstream-peers permit 10.2.1.1/32
!
ip prefix-list pl-cust1-network permit 10.3.1.0/24
ip prefix-list pl-cust1-network permit 10.3.2.0/24
!
ip prefix-list pl-cust2-network permit 10.4.1.0/24
!
ip prefix-list pl-peer1-network permit 10.5.1.0/24
ip prefix-list pl-peer1-network permit 10.5.2.0/24
ip prefix-list pl-peer1-network permit 192.168.0.0/24
!
ip prefix-list pl-peer2-network permit 10.6.1.0/24
ip prefix-list pl-peer2-network permit 10.6.2.0/24
ip prefix-list pl-peer2-network permit 192.168.1.0/24
ip prefix-list pl-peer2-network permit 192.168.2.0/24
ip prefix-list pl-peer2-network permit 172.16.1/24
!
bgp as-path access-list seq 5 asp-own-as permit ^$
bgp as-path access-list seq 10 asp-own-as permit _64512_
!
! #################################################################
! Match communities we provide actions for, on routes receives from
! customers. Communities values of <our-ASN>:X, with X, have actions:
!
! 100 - blackhole the prefix
! 200 - set no_export
! 300 - advertise only to other customers
! 400 - advertise only to upstreams
! 500 - set no_export when advertising to upstreams
! 2X00 - set local_preference to X00
!
! blackhole the prefix of the route
bgp community-list standard cm-blackhole permit 64512:100
!
! set no-export community before advertising
bgp community-list standard cm-set-no-export permit 64512:200
!
! advertise only to other customers
bgp community-list standard cm-cust-only permit 64512:300
!
! advertise only to upstreams
bgp community-list standard cm-upstream-only permit 64512:400
!
! advertise to upstreams with no-export
bgp community-list standard cm-upstream-noexport permit 64512:500
!
! set local-pref to least significant 3 digits of the community
bgp community-list standard cm-prefmod-100 permit 64512:2100
bgp community-list standard cm-prefmod-200 permit 64512:2200
bgp community-list standard cm-prefmod-300 permit 64512:2300
bgp community-list standard cm-prefmod-400 permit 64512:2400
bgp community-list expanded cme-prefmod-range permit 64512:2...
!
! Informational communities
!
! 3000 - learned from upstream
! 3100 - learned from customer
! 3200 - learned from peer
!
bgp community-list standard cm-learnt-upstream permit 64512:3000
bgp community-list standard cm-learnt-cust permit 64512:3100
bgp community-list standard cm-learnt-peer permit 64512:3200
!
! ###################################################################
! Utility route-maps
!
! These utility route-maps generally should not used to permit/deny
! routes, i.e. they do not have meaning as filters, and hence probably
! should be used with 'on-match next'. These all finish with an empty
! permit entry so as not interfere with processing in the caller.
!
route-map rm-no-export permit 10
set community additive no-export
route-map rm-no-export permit 20
!
route-map rm-blackhole permit 10
description blackhole, up-pref and ensure it cannot escape this AS
set ip next-hop 127.0.0.1
set local-preference 10
set community additive no-export
route-map rm-blackhole permit 20
!
! Set local-pref as requested
route-map rm-prefmod permit 10
match community cm-prefmod-100
set local-preference 100
route-map rm-prefmod permit 20
match community cm-prefmod-200
set local-preference 200
route-map rm-prefmod permit 30
match community cm-prefmod-300
set local-preference 300
route-map rm-prefmod permit 40
match community cm-prefmod-400
set local-preference 400
route-map rm-prefmod permit 50
!
! Community actions to take on receipt of route.
route-map rm-community-in permit 10
description check for blackholing, no point continuing if it matches.
match community cm-blackhole
call rm-blackhole
route-map rm-community-in permit 20
match community cm-set-no-export
call rm-no-export
on-match next
route-map rm-community-in permit 30
match community cme-prefmod-range
call rm-prefmod
route-map rm-community-in permit 40
!
! #####################################################################
! Community actions to take when advertising a route.
! These are filtering route-maps,
!
! Deny customer routes to upstream with cust-only set.
route-map rm-community-filt-to-upstream deny 10
match community cm-learnt-cust
match community cm-cust-only
route-map rm-community-filt-to-upstream permit 20
!
! Deny customer routes to other customers with upstream-only set.
route-map rm-community-filt-to-cust deny 10
match community cm-learnt-cust
match community cm-upstream-only
route-map rm-community-filt-to-cust permit 20
!
! ###################################################################
! The top-level route-maps applied to sessions. Further entries could
! be added obviously..
!
! Customers
route-map rm-cust-in permit 10
call rm-community-in
on-match next
route-map rm-cust-in permit 20
set community additive 64512:3100
route-map rm-cust-in permit 30
!
route-map rm-cust-out permit 10
call rm-community-filt-to-cust
on-match next
route-map rm-cust-out permit 20
!
! Upstream transit ASes
route-map rm-upstream-out permit 10
description filter customer prefixes which are marked cust-only
call rm-community-filt-to-upstream
on-match next
route-map rm-upstream-out permit 20
description only customer routes are provided to upstreams/peers
match community cm-learnt-cust
!
! Peer ASes
! outbound policy is same as for upstream
route-map rm-peer-out permit 10
call rm-upstream-out
!
route-map rm-peer-in permit 10
set community additive 64512:3200
Example of how to set up a 6-Bone connection.
! bgpd configuration
! ==================
!
! MP-BGP configuration
!
router bgp 7675
bgp router-id 10.0.0.1
neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 remote-as `as-number`
!
address-family ipv6
network 3ffe:506::/32
neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 activate
neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 route-map set-nexthop out
neighbor 3ffe:1cfa:0:2:2c0:4fff:fe68:a231 remote-as `as-number`
neighbor 3ffe:1cfa:0:2:2c0:4fff:fe68:a231 route-map set-nexthop out
exit-address-family
!
ipv6 access-list all permit any
!
! Set output nexthop address.
!
route-map set-nexthop permit 10
match ipv6 address all
set ipv6 nexthop global 3ffe:1cfa:0:2:2c0:4fff:fe68:a225
set ipv6 nexthop local fe80::2c0:4fff:fe68:a225
!
log syslog
!
BGP tcp-mss support
TCP provides a mechanism for the user to specify the max segment size. setsockopt API is used to set the max segment size for TCP session. We can configure this as part of BGP neighbor configuration.
This document explains how to avoid ICMP vulnerability issues by limiting TCP max segment size when you are using MTU discovery. Using MTU discovery on TCP paths is one method of avoiding BGP packet fragmentation.
TCP negotiates a maximum segment size (MSS) value during session connection establishment between two peers. The MSS value negotiated is primarily based on the maximum transmission unit (MTU) of the interfaces to which the communicating peers are directly connected. However, due to variations in link MTU on the path taken by the TCP packets, some packets in the network that are well within the MSS value might be fragmented when the packet size exceeds the link’s MTU.
This feature is supported with TCP over IPv4 and TCP over IPv6.
CLI Configuration:
Below configuration can be done in router bgp mode and allows the user to configure the tcp-mss value per neighbor. The configuration gets applied only after hard reset is performed on that neighbor. If we configure tcp-mss on both the neighbors then both neighbors need to be reset.
The configuration takes effect based on below rules, so there is a configured tcp-mss and a synced tcp-mss value per TCP session.
By default if the configuration is not done then the TCP max segment size is set to the Maximum Transmission unit (MTU) – (IP/IP6 header size + TCP header size + ethernet header). For IPv4 its MTU – (20 bytes IP header + 20 bytes TCP header + 12 bytes ethernet header) and for IPv6 its MTU – (40 bytes IPv6 header + 20 bytes TCP header + 12 bytes ethernet header).
If the config is done then it reduces 12-14 bytes for the ether header and uses it after synchronizing in TCP handshake.
- neighbor <A.B.C.D|X:X::X:X|WORD> tcp-mss (1-65535)
When tcp-mss is configured kernel reduces 12-14 bytes for ethernet header. E.g. if tcp-mss is configured as 150 the synced value will be 138.
Note: configured and synced value is different since TCP module will reduce 12 bytes for ethernet header.
Running config:
soodar# show running-config
Building configuration...
Current configuration:
!
router bgp 100
bgp router-id 192.0.2.1
neighbor 198.51.100.2 remote-as 100
neighbor 198.51.100.2 tcp-mss 150 => new entry
neighbor 2001:DB8::2 remote-as 100
neighbor 2001:DB8::2 tcp-mss 400 => new entry
Show command:
soodar# show bgp neighbors 198.51.100.2
BGP neighbor is 198.51.100.2, remote AS 100, local AS 100, internal link
Hostname: frr
BGP version 4, remote router ID 192.0.2.2, local router ID 192.0.2.1
BGP state = Established, up for 02:15:28
Last read 00:00:28, Last write 00:00:28
Hold time is 180, keepalive interval is 60 seconds
Configured tcp-mss is 150, synced tcp-mss is 138 => new display
soodar# show bgp neighbors 2001:DB8::2
BGP neighbor is 2001:DB8::2, remote AS 100, local AS 100, internal link
Hostname: frr
BGP version 4, remote router ID 192.0.2.2, local router ID 192.0.2.1
BGP state = Established, up for 02:16:34
Last read 00:00:34, Last write 00:00:34
Hold time is 180, keepalive interval is 60 seconds
Configured tcp-mss is 400, synced tcp-mss is 388 => new display
Show command json output:
soodar# show bgp neighbors 2001:DB8::2 json
{
"2001:DB8::2":{
"remoteAs":100,
"localAs":100,
"nbrInternalLink":true,
"hostname":"frr",
"bgpVersion":4,
"remoteRouterId":"192.0.2.2",
"localRouterId":"192.0.2.1",
"bgpState":"Established",
"bgpTimerUpMsec":8349000,
"bgpTimerUpString":"02:19:09",
"bgpTimerUpEstablishedEpoch":1613054251,
"bgpTimerLastRead":9000,
"bgpTimerLastWrite":9000,
"bgpInUpdateElapsedTimeMsecs":8347000,
"bgpTimerHoldTimeMsecs":180000,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":400, => new entry
"bgpTcpMssSynced":388, => new entry
soodar# show bgp neighbors 198.51.100.2 json
{
"198.51.100.2":{
"remoteAs":100,
"localAs":100,
"nbrInternalLink":true,
"hostname":"frr",
"bgpVersion":4,
"remoteRouterId":"192.0.2.2",
"localRouterId":"192.0.2.1",
"bgpState":"Established",
"bgpTimerUpMsec":8370000,
"bgpTimerUpString":"02:19:30",
"bgpTimerUpEstablishedEpoch":1613054251,
"bgpTimerLastRead":30000,
"bgpTimerLastWrite":30000,
"bgpInUpdateElapsedTimeMsecs":8368000,
"bgpTimerHoldTimeMsecs":180000,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":150, => new entry
"bgpTcpMssSynced":138, => new entry
Configuring FRR as a Route Server
The purpose of a Route Server is to centralize the peerings between BGP speakers. For example if we have an exchange point scenario with four BGP speakers, each of which maintaining a BGP peering with the other three (Full Mesh), we can convert it into a centralized scenario where each of the four establishes a single BGP peering against the Route Server (Route server and clients).
We will first describe briefly the Route Server model implemented by FRR. We will explain the commands that have been added for configuring that model. And finally we will show a full example of FRR configured as Route Server.
Description of the Route Server model
First we are going to describe the normal processing that BGP announcements suffer inside a standard BGP speaker, as shown in Announcement processing inside a ‘normal’ BGP speaker, it consists of three steps:
When an announcement is received from some peer, the In filters configured for that peer are applied to the announcement. These filters can reject the announcement, accept it unmodified, or accept it with some of its attributes modified.
The announcements that pass the In filters go into the Best Path Selection process, where they are compared to other announcements referred to the same destination that have been received from different peers (in case such other announcements exist). For each different destination, the announcement which is selected as the best is inserted into the BGP speaker’s Loc-RIB.
The routes which are inserted in the Loc-RIB are considered for announcement to all the peers (except the one from which the route came). This is done by passing the routes in the Loc-RIB through the Out filters corresponding to each peer. These filters can reject the route, accept it unmodified, or accept it with some of its attributes modified. Those routes which are accepted by the Out filters of a peer are announced to that peer.
Of course we want that the routing tables obtained in each of the routers are the same when using the route server than when not. But as a consequence of having a single BGP peering (against the route server), the BGP speakers can no longer distinguish from/to which peer each announce comes/goes.
This means that the routers connected to the route server are not able to apply by themselves the same input/output filters as in the full mesh scenario, so they have to delegate those functions to the route server.
Even more, the ‘best path’ selection must be also performed inside the route server on behalf of its clients. The reason is that if, after applying the filters of the announcer and the (potential) receiver, the route server decides to send to some client two or more different announcements referred to the same destination, the client will only retain the last one, considering it as an implicit withdrawal of the previous announcements for the same destination. This is the expected behavior of a BGP speaker as defined in RFC 1771, and even though there are some proposals of mechanisms that permit multiple paths for the same destination to be sent through a single BGP peering, none are currently supported by most existing BGP implementations.
As a consequence a route server must maintain additional information and perform additional tasks for a RS-client that those necessary for common BGP peerings. Essentially a route server must:
Maintain a separated Routing Information Base (Loc-RIB) for each peer configured as RS-client, containing the routes selected as a result of the ‘Best Path Selection’ process that is performed on behalf of that RS-client.
Whenever it receives an announcement from a RS-client, it must consider it for the Loc-RIBs of the other RS-clients.
This means that for each of them the route server must pass the announcement through the appropriate Out filter of the announcer.
Then through the appropriate In filter of the potential receiver.
Only if the announcement is accepted by both filters it will be passed to the ‘Best Path Selection’ process.
Finally, it might go into the Loc-RIB of the receiver.
When we talk about the ‘appropriate’ filter, both the announcer and the receiver of the route must be taken into account. Suppose that the route server receives an announcement from client A, and the route server is considering it for the Loc-RIB of client B. The filters that should be applied are the same that would be used in the full mesh scenario, i.e., first the Out filter of router A for announcements going to router B, and then the In filter of router B for announcements coming from router A.
We call ‘Export Policy’ of a RS-client to the set of Out filters that the client would use if there was no route server. The same applies for the ‘Import Policy’ of a RS-client and the set of In filters of the client if there was no route server.
It is also common to demand from a route server that it does not modify some BGP attributes (next-hop, as-path and MED) that are usually modified by standard BGP speakers before announcing a route.
The announcement processing model implemented by FRR is shown in Announcement processing model implemented by the Route Server. The figure shows a mixture of RS-clients (B, C and D) with normal BGP peers (A). There are some details that worth additional comments:
Announcements coming from a normal BGP peer are also considered for the Loc-RIBs of all the RS-clients. But logically they do not pass through any export policy.
Those peers that are configured as RS-clients do not receive any announce from the Main Loc-RIB.
Apart from import and export policies, In and Out filters can also be set for RS-clients. In filters might be useful when the route server has also normal BGP peers. On the other hand, Out filters for RS-clients are probably unnecessary, but we decided not to remove them as they do not hurt anybody (they can always be left empty).
Commands for configuring a Route Server
Now we will describe the commands that have been added to frr in order to support the route server features.
- neighbor PEER-GROUP route-server-client
- neighbor A.B.C.D route-server-client
- neighbor X:X::X:X route-server-client
This command configures the peer given by peer, A.B.C.D or X:X::X:X as an RS-client.
Actually this command is not new, it already existed in standard FRR. It enables the transparent mode for the specified peer. This means that some BGP attributes (as-path, next-hop and MED) of the routes announced to that peer are not modified.
With the route server patch, this command, apart from setting the transparent mode, creates a new Loc-RIB dedicated to the specified peer (those named Loc-RIB for X in Announcement processing model implemented by the Route Server.). Starting from that moment, every announcement received by the route server will be also considered for the new Loc-RIB.
- neigbor A.B.C.D|X.X::X.X|peer-group route-map WORD in|out
This set of commands can be used to specify the route-map that represents the Import or Export policy of a peer which is configured as a RS-client (with the previous command).
- match peer A.B.C.D|X:X::X:X
This is a new match statement for use in route-maps, enabling them to describe import/export policies. As we said before, an import/export policy represents a set of input/output filters of the RS-client. This statement makes possible that a single route-map represents the full set of filters that a BGP speaker would use for its different peers in a non-RS scenario.
The match peer statement has different semantics whether it is used inside an import or an export route-map. In the first case the statement matches if the address of the peer who sends the announce is the same that the address specified by {A.B.C.D|X:X::X:X}. For export route-maps it matches when {A.B.C.D|X:X::X:X} is the address of the RS-Client into whose Loc-RIB the announce is going to be inserted (how the same export policy is applied before different Loc-RIBs is shown in Announcement processing model implemented by the Route Server.).
- call WORD
This command (also used inside a route-map) jumps into a different route-map, whose name is specified by WORD. When the called route-map finishes, depending on its result the original route-map continues or not. Apart from being useful for making import/export route-maps easier to write, this command can also be used inside any normal (in or out) route-map.
Example of Route Server Configuration
Finally we are going to show how to configure a FRR daemon to act as a Route Server. For this purpose we are going to present a scenario without route server, and then we will show how to use the configurations of the BGP routers to generate the configuration of the route server.
All the configuration files shown in this section have been taken from scenarios which were tested using the VNUML tool http://www.dit.upm.es/vnuml,VNUML.
Configuration of the BGP routers without Route Server
We will suppose that our initial scenario is an exchange point with three BGP capable routers, named RA, RB and RC. Each of the BGP speakers generates some routes (with the network command), and establishes BGP peerings against the other two routers. These peerings have In and Out route-maps configured, named like ‘PEER-X-IN’ or ‘PEER-X-OUT’. For example the configuration file for router RA could be the following:
#Configuration for router 'RA'
!
hostname RA
password ****
!
router bgp 65001
no bgp default ipv4-unicast
neighbor 2001:0DB8::B remote-as 65002
neighbor 2001:0DB8::C remote-as 65003
!
address-family ipv6
network 2001:0DB8:AAAA:1::/64
network 2001:0DB8:AAAA:2::/64
network 2001:0DB8:0000:1::/64
network 2001:0DB8:0000:2::/64
neighbor 2001:0DB8::B activate
neighbor 2001:0DB8::B soft-reconfiguration inbound
neighbor 2001:0DB8::B route-map PEER-B-IN in
neighbor 2001:0DB8::B route-map PEER-B-OUT out
neighbor 2001:0DB8::C activate
neighbor 2001:0DB8::C soft-reconfiguration inbound
neighbor 2001:0DB8::C route-map PEER-C-IN in
neighbor 2001:0DB8::C route-map PEER-C-OUT out
exit-address-family
!
ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
!
route-map PEER-B-IN permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set metric 100
route-map PEER-B-IN permit 20
match ipv6 address prefix-list PEER-B-PREFIXES
set community 65001:11111
!
route-map PEER-C-IN permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set metric 200
route-map PEER-C-IN permit 20
match ipv6 address prefix-list PEER-C-PREFIXES
set community 65001:22222
!
route-map PEER-B-OUT permit 10
match ipv6 address prefix-list PEER-A-PREFIXES
!
route-map PEER-C-OUT permit 10
match ipv6 address prefix-list PEER-A-PREFIXES
!
line vty
!
Configuration of the BGP routers with Route Server
To convert the initial scenario into one with route server, first we must modify the configuration of routers RA, RB and RC. Now they must not peer between them, but only with the route server. For example, RA’s configuration would turn into:
# Configuration for router 'RA'
!
hostname RA
password ****
!
router bgp 65001
no bgp default ipv4-unicast
neighbor 2001:0DB8::FFFF remote-as 65000
!
address-family ipv6
network 2001:0DB8:AAAA:1::/64
network 2001:0DB8:AAAA:2::/64
network 2001:0DB8:0000:1::/64
network 2001:0DB8:0000:2::/64
neighbor 2001:0DB8::FFFF activate
neighbor 2001:0DB8::FFFF soft-reconfiguration inbound
exit-address-family
!
line vty
!
Which is logically much simpler than its initial configuration, as it now maintains only one BGP peering and all the filters (route-maps) have disappeared.
Configuration of the Route Server itself
As we said when we described the functions of a route server (Description of the Route Server model), it is in charge of all the route filtering. To achieve that, the In and Out filters from the RA, RB and RC configurations must be converted into Import and Export policies in the route server.
This is a fragment of the route server configuration (we only show the policies for client RA):
# Configuration for Route Server ('RS')
!
hostname RS
password ix
!
router bgp 65000 view RS
no bgp default ipv4-unicast
neighbor 2001:0DB8::A remote-as 65001
neighbor 2001:0DB8::B remote-as 65002
neighbor 2001:0DB8::C remote-as 65003
!
address-family ipv6
neighbor 2001:0DB8::A activate
neighbor 2001:0DB8::A route-server-client
neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT in
neighbor 2001:0DB8::A route-map RSCLIENT-A-EXPORT out
neighbor 2001:0DB8::A soft-reconfiguration inbound
neighbor 2001:0DB8::B activate
neighbor 2001:0DB8::B route-server-client
neighbor 2001:0DB8::B route-map RSCLIENT-B-IMPORT in
neighbor 2001:0DB8::B route-map RSCLIENT-B-EXPORT out
neighbor 2001:0DB8::B soft-reconfiguration inbound
neighbor 2001:0DB8::C activate
neighbor 2001:0DB8::C route-server-client
neighbor 2001:0DB8::C route-map RSCLIENT-C-IMPORT in
neighbor 2001:0DB8::C route-map RSCLIENT-C-EXPORT out
neighbor 2001:0DB8::C soft-reconfiguration inbound
exit-address-family
!
ipv6 prefix-list COMMON-PREFIXES seq 5 permit 2001:0DB8:0000::/48 ge 64 le 64
ipv6 prefix-list COMMON-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-A-PREFIXES seq 5 permit 2001:0DB8:AAAA::/48 ge 64 le 64
ipv6 prefix-list PEER-A-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-B-PREFIXES seq 5 permit 2001:0DB8:BBBB::/48 ge 64 le 64
ipv6 prefix-list PEER-B-PREFIXES seq 10 deny any
!
ipv6 prefix-list PEER-C-PREFIXES seq 5 permit 2001:0DB8:CCCC::/48 ge 64 le 64
ipv6 prefix-list PEER-C-PREFIXES seq 10 deny any
!
route-map RSCLIENT-A-IMPORT permit 10
match peer 2001:0DB8::B
call A-IMPORT-FROM-B
route-map RSCLIENT-A-IMPORT permit 20
match peer 2001:0DB8::C
call A-IMPORT-FROM-C
!
route-map A-IMPORT-FROM-B permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set metric 100
route-map A-IMPORT-FROM-B permit 20
match ipv6 address prefix-list PEER-B-PREFIXES
set community 65001:11111
!
route-map A-IMPORT-FROM-C permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set metric 200
route-map A-IMPORT-FROM-C permit 20
match ipv6 address prefix-list PEER-C-PREFIXES
set community 65001:22222
!
route-map RSCLIENT-A-EXPORT permit 10
match peer 2001:0DB8::B
match ipv6 address prefix-list PEER-A-PREFIXES
route-map RSCLIENT-A-EXPORT permit 20
match peer 2001:0DB8::C
match ipv6 address prefix-list PEER-A-PREFIXES
!
...
...
...
If you compare the initial configuration of RA with the route server configuration above, you can see how easy it is to generate the Import and Export policies for RA from the In and Out route-maps of RA’s original configuration.
When there was no route server, RA maintained two peerings, one with RB and another with RC. Each of this peerings had an In route-map configured. To build the Import route-map for client RA in the route server, simply add route-map entries following this scheme:
route-map <NAME> permit 10
match peer <Peer Address>
call <In Route-Map for this Peer>
route-map <NAME> permit 20
match peer <Another Peer Address>
call <In Route-Map for this Peer>
This is exactly the process that has been followed to generate the route-map RSCLIENT-A-IMPORT. The route-maps that are called inside it (A-IMPORT-FROM-B and A-IMPORT-FROM-C) are exactly the same than the In route-maps from the original configuration of RA (PEER-B-IN and PEER-C-IN), only the name is different.
The same could have been done to create the Export policy for RA (route-map RSCLIENT-A-EXPORT), but in this case the original Out route-maps where so simple that we decided not to use the call WORD commands, and we integrated all in a single route-map (RSCLIENT-A-EXPORT).
The Import and Export policies for RB and RC are not shown, but the process would be identical.
Further considerations about Import and Export route-maps
The current version of the route server patch only allows to specify a route-map for import and export policies, while in a standard BGP speaker apart from route-maps there are other tools for performing input and output filtering (access-lists, community-lists, …). But this does not represent any limitation, as all kinds of filters can be included in import/export route-maps. For example suppose that in the non-route-server scenario peer RA had the following filters configured for input from peer B:
neighbor 2001:0DB8::B prefix-list LIST-1 in
neighbor 2001:0DB8::B filter-list LIST-2 in
neighbor 2001:0DB8::B route-map PEER-B-IN in
...
...
route-map PEER-B-IN permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set local-preference 100
route-map PEER-B-IN permit 20
match ipv6 address prefix-list PEER-B-PREFIXES
set community 65001:11111
It is possible to write a single route-map which is equivalent to the three filters (the community-list, the prefix-list and the route-map). That route-map can then be used inside the Import policy in the route server. Lets see how to do it:
neighbor 2001:0DB8::A route-map RSCLIENT-A-IMPORT in
...
!
...
route-map RSCLIENT-A-IMPORT permit 10
match peer 2001:0DB8::B
call A-IMPORT-FROM-B
...
...
!
route-map A-IMPORT-FROM-B permit 1
match ipv6 address prefix-list LIST-1
match as-path LIST-2
on-match goto 10
route-map A-IMPORT-FROM-B deny 2
route-map A-IMPORT-FROM-B permit 10
match ipv6 address prefix-list COMMON-PREFIXES
set local-preference 100
route-map A-IMPORT-FROM-B permit 20
match ipv6 address prefix-list PEER-B-PREFIXES
set community 65001:11111
!
...
...
The route-map A-IMPORT-FROM-B is equivalent to the three filters (LIST-1, LIST-2 and PEER-B-IN). The first entry of route-map A-IMPORT-FROM-B (sequence number 1) matches if and only if both the prefix-list LIST-1 and the filter-list LIST-2 match. If that happens, due to the ‘on-match goto 10’ statement the next route-map entry to be processed will be number 10, and as of that point route-map A-IMPORT-FROM-B is identical to PEER-B-IN. If the first entry does not match, on-match goto 10’ will be ignored and the next processed entry will be number 2, which will deny the route.
Thus, the result is the same that with the three original filters, i.e., if either LIST-1 or LIST-2 rejects the route, it does not reach the route-map PEER-B-IN. In case both LIST-1 and LIST-2 accept the route, it passes to PEER-B-IN, which can reject, accept or modify the route.
Weighted ECMP using BGP link bandwidth
Overview
In normal equal cost multipath (ECMP), the route to a destination has multiple next hops and traffic is expected to be equally distributed across these next hops. In practice, flow-based hashing is used so that all traffic associated with a particular flow uses the same next hop, and by extension, the same path across the network.
Weighted ECMP using BGP link bandwidth introduces support for network-wide
unequal cost multipathing (UCMP) to an IP destination. The unequal cost
load balancing is implemented by the forwarding plane based on the weights
associated with the next hops of the IP prefix. These weights are computed
based on the bandwidths of the corresponding multipaths which are encoded
in the BGP link bandwidth extended community
as specified in
[Draft-IETF-idr-link-bandwidth]. Exchange of an appropriate BGP link
bandwidth value for a prefix across the network results in network-wide
unequal cost multipathing.
One of the primary use cases of this capability is in the data center when a service (represented by its anycast IP) has an unequal set of resources across the regions (e.g., PODs) of the data center and the network itself provides the load balancing function instead of an external load balancer. Refer to [Draft-IETF-mohanty-bess-ebgp-dmz] and RFC 7938 for details on this use case. This use case is applicable in a pure L3 network as well as in a EVPN network.
The traditional use case for BGP link bandwidth to load balance traffic to the exit routers in the AS based on the bandwidth of their external eBGP peering links is also supported.
Design Principles
Next hop weight computation and usage
As described, in UCMP, there is a weight associated with each next hop of an IP prefix, and traffic is expected to be distributed across the next hops in proportion to their weight. The weight of a next hop is a simple factoring of the bandwidth of the corresponding path against the total bandwidth of all multipaths, mapped to the range 1 to 100. What happens if not all the paths in the multipath set have link bandwidth associated with them? In such a case, in adherence to [Draft-IETF-idr-link-bandwidth], the behavior reverts to standard ECMP among all the multipaths, with the link bandwidth being effectively ignored.
Note that there is no change to either the BGP best path selection algorithm or to the multipath computation algorithm; the mapping of link bandwidth to weight happens at the time of installation of the route in the RIB.
If data forwarding is implemented by means of the Linux kernel, the next hop’s weight is used in the hash calculation. The kernel uses the Hash threshold algorithm and use of the next hop weight is built into it; next hops need not be expanded to achieve UCMP. UCMP for IPv4 is available in older Linux kernels too, while UCMP for IPv6 is available from the 4.16 kernel onwards.
If data forwarding is realized in hardware, common implementations expand the next hops (i.e., they are repeated) in the ECMP container in proportion to their weight. For example, if the weights associated with 3 next hops for a particular route are 50, 25 and 25 and the ECMP container has a size of 16 next hops, the first next hop will be repeated 8 times and the other 2 next hops repeated 4 times each. Other implementations are also possible.
Unequal cost multipath across a network
For the use cases listed above, it is not sufficient to support UCMP on just one router (e.g., egress router), or individually, on multiple routers; UCMP must be deployed across the entire network. This is achieved by employing the BGP link-bandwidth extended community.
At the router which originates the BGP link bandwidth, there has to be user configuration to trigger it, which is described below. Receiving routers would use the received link bandwidth from their downstream routers to determine the next hop weight as described in the earlier section. Further, if the received link bandwidth is a transitive attribute, it would be propagated to eBGP peers, with the additional change that if the next hop is set to oneself, the cumulative link bandwidth of all downstream paths is propagated to other routers. In this manner, the entire network will know how to distribute traffic to an anycast service across the network.
The BGP link-bandwidth extended community is encoded in bytes-per-second. In the use case where UCMP must be based on the number of paths, a reference bandwidth of 1 Mbps is used. So, for example, if there are 4 equal cost paths to an anycast IP, the encoded bandwidth in the extended community will be 500,000. The actual value itself doesn’t matter as long as all routers originating the link-bandwidth are doing it in the same way.
Configuration Guide
The configuration for weighted ECMP using BGP link bandwidth requires one essential step - using a route-map to inject the link bandwidth extended community. An additional option is provided to control the processing of received link bandwidth.
Injecting link bandwidth into the network
At the “entry point” router that is injecting the prefix to which weighted load balancing must be performed, a route-map must be configured to attach the link bandwidth extended community.
For the use case of providing weighted load balancing for an anycast service, this configuration will typically need to be applied at the TOR or Leaf router that is connected to servers which provide the anycast service and the bandwidth would be based on the number of multipaths for the destination.
For the use case of load balancing to the exit router, the exit router should be configured with the route map specifying the a bandwidth value that corresponds to the bandwidth of the link connecting to its eBGP peer in the adjoining AS. In addition, the link bandwidth extended community must be explicitly configured to be non-transitive.
The complete syntax of the route-map set command can be found at BGP Extended Communities in Route Map
This route-map is supported only at two attachment points: (a) the outbound route-map attached to a peer or peer-group, per address-family (b) the EVPN advertise route-map used to inject IPv4 or IPv6 unicast routes into EVPN as type-5 routes.
Since the link bandwidth origination is done by using a route-map, it can be constrained to certain prefixes (e.g., only for anycast services) or it can be generated for all prefixes. Further, when the route-map is used in the neighbor context, the link bandwidth usage can be constrained to certain peers only.
A sample configuration is shown below and illustrates link bandwidth advertisement towards the “SPINE” peer-group for anycast IPs in the range 192.168.x.x
ip prefix-list anycast_ip seq 10 permit 192.168.0.0/16 le 32
route-map anycast_ip permit 10
match ip address prefix-list anycast_ip
set extcommunity bandwidth num-multipaths
route-map anycast_ip permit 20
!
router bgp 65001
neighbor SPINE peer-group
neighbor SPINE remote-as external
neighbor 172.16.35.1 peer-group SPINE
neighbor 172.16.36.1 peer-group SPINE
!
address-family ipv4 unicast
network 110.0.0.1/32
network 192.168.44.1/32
neighbor SPINE route-map anycast_ip out
exit-address-family
!
Controlling link bandwidth processing on the receiver
There is no configuration necessary to process received link bandwidth and translate it into the weight associated with the corresponding next hop; that happens by default. If some of the multipaths do not have the link bandwidth extended community, the default behavior is to revert to normal ECMP as recommended in [Draft-IETF-idr-link-bandwidth].
The operator can change these behaviors with the following configuration:
- bgp bestpath bandwidth <ignore | skip-missing | default-weight-for-missing>
The different options imply behavior as follows:
ignore: Ignore link bandwidth completely for route installation (i.e., do regular ECMP, not weighted)
skip-missing: Skip paths without link bandwidth and do UCMP among the others (if at least some paths have link-bandwidth)
default-weight-for-missing: Assign a low default weight (value 1) to paths not having link bandwidth
This configuration is per BGP instance similar to other BGP route-selection controls; it operates on both IPv4-unicast and IPv6-unicast routes in that instance. In an EVPN network, this configuration (if required) should be implemented in the tenant VRF and is again applicable for IPv4-unicast and IPv6-unicast, including the ones sourced from EVPN type-5 routes.
A sample snippet of FRR configuration on a receiver to skip paths without link bandwidth and do weighted ECMP among the other paths (if some of them have link bandwidth) is as shown below.
router bgp 65021
bgp bestpath as-path multipath-relax
bgp bestpath bandwidth skip-missing
neighbor LEAF peer-group
neighbor LEAF remote-as external
neighbor 172.16.35.2 peer-group LEAF
neighbor 172.16.36.2 peer-group LEAF
!
address-family ipv4 unicast
network 130.0.0.1/32
exit-address-family
!
Stopping the propagation of the link bandwidth outside a domain
The link bandwidth extended community will get automatically propagated with the prefix to EBGP peers, if it is encoded as a transitive attribute by the originator. If this propagation has to be stopped outside of a particular domain (e.g., stopped from being propagated to routers outside of the data center core network), the mechanism available is to disable the advertisement of all BGP extended communities on the specific peering/s. In other words, the propagation cannot be blocked just for the link bandwidth extended community. The configuration to disable all extended communities can be applied to a peer or peer-group (per address-family).
Of course, the other common way to stop the propagation of the link bandwidth outside the domain is to block the prefixes themselves from being advertised and possibly, announce only an aggregate route. This would be quite common in a EVPN network.
BGP link bandwidth and UCMP monitoring & troubleshooting
Existing operational commands to display the BGP routing table for a specific prefix will show the link bandwidth extended community also, if present.
An example of an IPv4-unicast route received with the link bandwidth attribute from two peers is shown below:
CLI# show bgp ipv4 unicast 192.168.10.1/32
BGP routing table entry for 192.168.10.1/32
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
l1(swp1) l2(swp2) l3(swp3) l4(swp4)
65002
fe80::202:ff:fe00:1b from l2(swp2) (110.0.0.2)
(fe80::202:ff:fe00:1b) (used)
Origin IGP, metric 0, valid, external, multipath, bestpath-from-AS 65002
Extended Community: LB:65002:125000000 (1000.000 Mbps)
Last update: Thu Feb 20 18:34:16 2020
65001
fe80::202:ff:fe00:15 from l1(swp1) (110.0.0.1)
(fe80::202:ff:fe00:15) (used)
Origin IGP, metric 0, valid, external, multipath, bestpath-from-AS 65001, best (Older Path)
Extended Community: LB:65001:62500000 (500.000 Mbps)
Last update: Thu Feb 20 18:22:34 2020
The weights associated with the next hops of a route can be seen by querying the RIB for a specific route.
For example, the next hop weights corresponding to the link bandwidths in the above example is illustrated below:
spine1# show ip route 192.168.10.1/32
Routing entry for 192.168.10.1/32
Known via "bgp", distance 20, metric 0, best
Last update 00:00:32 ago
* fe80::202:ff:fe00:1b, via swp2, weight 66
* fe80::202:ff:fe00:15, via swp1, weight 33
For troubleshooting, existing debug logs debug bgp updates
,
debug bgp bestpath <prefix>
, debug bgp zebra
and
debug zebra kernel
can be used.
A debug log snippet when debug bgp zebra
is enabled and a route is
installed by BGP in the RIB with next hop weights is shown below:
2020-02-29T06:26:19.927754+00:00 leaf1 bgpd[5459]: bgp_zebra_announce: p=192.168.150.1/32, bgp_is_valid_label: 0
2020-02-29T06:26:19.928096+00:00 leaf1 bgpd[5459]: Tx route add VRF 33 192.168.150.1/32 metric 0 tag 0 count 2
2020-02-29T06:26:19.928289+00:00 leaf1 bgpd[5459]: nhop [1]: 110.0.0.6 if 35 VRF 33 wt 50 RMAC 0a:11:2f:7d:35:20
2020-02-29T06:26:19.928479+00:00 leaf1 bgpd[5459]: nhop [2]: 110.0.0.5 if 35 VRF 33 wt 50 RMAC 32:1e:32:a3:6c:bf
2020-02-29T06:26:19.928668+00:00 leaf1 bgpd[5459]: bgp_zebra_announce: 192.168.150.1/32: announcing to zebra (recursion NOT set)
References
McPherson, D. and Gill, V. and Walton, D., “Border Gateway Protocol (BGP) Persistent Route Oscillation Condition”, IETF RFC3345
Flavel, A. and M. Roughan, “Stable and flexible iBGP”, ACM SIGCOMM 2009
Griffin, T. and G. Wilfong, “On the correctness of IBGP configuration”, ACM SIGCOMM 2002
BGP fast-convergence support
Whenever BGP peer address becomes unreachable we must bring down the BGP session immediately. Currently only single-hop EBGP sessions are brought down immediately.IBGP and multi-hop EBGP sessions wait for hold-timer expiry to bring down the sessions.
This new configuration option helps user to teardown BGP sessions immediately whenever peer becomes unreachable.
- bgp fast-convergence
This configuration is available at the bgp level. When enabled, configuration is applied to all the neighbors configured in that bgp instance.
router bgp 64496
neighbor 10.0.0.2 remote-as 64496
neighbor fd00::2 remote-as 64496
bgp fast-convergence
!
address-family ipv4 unicast
redistribute static
exit-address-family
!
address-family ipv6 unicast
neighbor fd00::2 activate
exit-address-family